Справочник Пользователя для State Industries GS675YRVLT

30

Please check guidelines below.  For your safety, water heater service should be performed only by a qualified service technician.  

Read the GENERAL SAFETY INFORMATION section first.

INTELLI-VENT TROUBLESHOOTING CHART - RESIDENTIAL CONTROL

 

 

 

Inadequate or no earth ground  

1. Ensure the wall outlet is properly grounded.

 

1 

sensed by the Intelli-Vent™

 

 

control. 

2. Ensure all ground connections/wires on the 

 

 

 

  water heater are secure.

 

 

 

 

 

 

Power supply to Intelli-Vent™ 

1. Ensure the wall outlet is properly wired.

 

2 

control has reversed polarity or a

 

 

high resistance to earth ground. 

2. Ensure all internal 120 VAC wiring connections and 

 

 

 

  wiring harness have no reversed wires. 120 VAC

 

 

 

  “hot” wire must connect to the on/off switch.

 

 

 

3. Ensure the wall outlet is properly grounded.

 

4. Ensure all ground connections/wires on the water

 

 

  heater are secure.

 

 

Pressure switch circuit remaining 

1. Ensure air pressure switch circuit wiring is correct

 

3 

closed for more than 5 seconds 

  and the air pressure switch is not jumpered.

 

 

after heating cycle begins.

 

 

2. Secure power to water heater, check continuity of air

 

 

 

  pressure switch contacts with wires disconnected.

 

 

service note: 

 

 

Disconnect power - disconnect one 

  A  If pressure switch contacts show continuity (closed

 

 

wire from the air pressure switch 

    circuit) replace the pressure switch.

 

 

or the vent temperature limit

 

 

switch. Turn power back on - 

  B  If pressure switch contacts are open and all wiring

 

 

blower should start. 

    is correct - turn the power off for 10-20 seconds

 

 

 

    then on again to clear the error code - if the error

 

 

 

    code persists replace the Intelli-Vent™ control.

 

 

 

 

 

Pressure switch circuit remains open 

1. Ensure the blower is running - check for 120 VAC to

 

4 

longer than 5 seconds after the blower 

  the blower when the heating cycle begins, check the

 

 

is energized. 

  wiring. If the control does not energize the blower -

 

 

 

  replace the Intelli-Vent™ control. If the blower fails to

 

 

Blower may run continuously in  

  start when energized - replace the blower assembly.

 

 

this condition. 

 

 

 

2. Ensure the air pressure switch sensing tube is properly 

 

 

 

  connected - not kinked or damaged.

 

 

 

3. Check continuity of vent temperature limit switch - replace

 

 

 

  switch if contacts remain open under 160ºF (71°C).

 

 

 

 

 

 

4. Ensure the correct size of vent pipe (2”, 3”, 4”) was used

 

 

service note: 

  per installation manual for vent length. Ensure maximum

 

 

To learn more about performing Air 

  number of elbows or equivalent feet of vent pipe has not

 

 

Pressure Switch tests visit our web 

  exceeded maximum limits.

 

 

site www.hotwater.com to download

 

 

technical bulletin A-023-06 Air Pressure 

5. Ensure there are no obstructions in the vent pipe.

 

 

Switches. 

 

 

 

6. Check air pressure switch performance - check pressure

 

 

 

  with a digital manometer - check continuity of contacts.

 

 

 

  (see service note in left column) If the switch proves  

 

 

 

  defective - replace the air pressure switch and or the

 

 

 

  blower assembly as required.

 

 

 

7. If air pressure switch performance test results prove

 

 

 

  the air pressure switch is working properly and error

 

 

 

  code 4 persists - replace the Intelli-Vent™ control.

 

 

The Intelli-Vent™ control has detected 

1. Check wiring to the hot surface ignitor - replace ignitor

 

5 

an open ignitor circuit. 

  assembly if wiring is damaged or worn.

 

 

 

 

 

service note: 

2. Check ignitor assembly plug and the socket on the

 

 

The resistance (ohms) of a hot surface 

  Intelli-Vent™ body for good connection. Replace

 

 

ignitor will increase over time. If the 

  ignitor assembly and/or control if necessary.

 

 

resistance at room temperature is near 

 

 

 

18.8 ohms - consider replacing the ignitor  3. Check resistance of ignitor at room temperature 77ºF 

 

 

as a preventative measure. 

  (25°C) at the plug end. Replace ignitor if resistance

 

 

 

  is not within 11.5 and 18.8 ohms at room temperature.

 

 

 

 

 

 

4. If results from the above tests were good and error

 

 

 

  code 5 persists - replace the Intelli-Vent™ control.