Справочник Пользователя для i. Tech Dynamic i.Cube

Getting Started

Before using your i.Cube (“headset”) for the first time, please ensure that

1. the headset is fully charged;
2. the fully charged headset must be paired and connected with a Bluetooth mobile

phone.

Charging Your Headset

The headset comes with a built-in rechargeable battery. Prior to using the headset for
the first time, you are recommended to fully charge the battery.

Use only the supplied charger to charge the headset.

Charging Socket

fig.2

Status

Status Indicator

Audio

• Charging

• Red light

• Fully charged

• Blue light

• Low battery

• Flashing red light

• a short beep every 1 minute

• Out of battery

• The light goes off

♦ 3 hours are required to fully charge the headset.

♦ Charging indication will be delayed for a few seconds if the headset has not been used

for a long time or the battery is drained.

Charging Your Headset (cont’d)

Pairing Your Headset with a Bluetooth Mobile Phone

1) Ensure the headset is off.
2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without

releasing your finger until its status indicator flashes alternating blue and red lights.

3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “i.Cube” and

enter the passcode “0000”. When the pairing is completed, the headset’s status indicator
will flash a blue light rapidly five times.

If the pairing cannot be completed within three minutes after the pairing mode has been
activated, the headset’s status indicator will flash purple rapidly five times and then turns
off. Repeat steps 1 to 3 to pair both devices again.

Pairing Your Headset with Two Mobile Phones (Multipoint)

i.Cube supports a Multipoint function to allow simultaneous pairing of the headset

with two mobile phones.

1. Follow the pairing procedure as instructed in “Pairing Your Headset with a

Bluetooth

Mobile Phone” to pair the headset with the first mobile phone.

2. Repeat the pairing procedure for the second mobile phone.

3. On the first mobile phone’s menu, activate its Bluetooth connection with the

headset.

When you turn on your headset for the first time, the headset automatically enters

the pairing mode, i.e. the status indicator flashes alternating blue and red lights.

This allows you to immediately pair your headset and mobile phone.
If your headset is paired with your mobile phone, press the MFB once more after

you turned on the headset to re-connect the mobile phone and the headset.

Using Your Headset

Using Your Headset (cont'd)

Function

Button

Audio

Status Indicator

Power ON

Press and hold the MFB for 2

a short beep Flashing blue light

seconds

Power OFF

Press and hold the MFB for 2

a long beep

seconds

Say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone.

Function Button Audio

Status Indicator

Answer a Call Press the MFB once

Flashing blue light

Answer a Second Call Press the MFB once to terminate a beep Flashing purple light
intended for your other the first call, then press the MFB when there is a second
mobile phone once again to answer the second call intended for your
call other mobile phone
End a Call Press the MFB once

Flashing blue light

Last No. Redial Double click the MFB

Flashing blue light

Adjust Volume Press the Vol＋/－once to a short beep

Flashing blue light

increase / decrease by 1 level
Mute a Call Press either volume key for 2      2 beeps every     Flashing blue light
seconds 5 seconds
Cancel Call Muting Press either volume key for 2 2 short beeps     Flashing blue light
seconds
Voice Dialing Press the MFB once     a short beep

Flashing blue light

Red light for two seconds
and then the light goes off

If you do not plan to use the headset for a while, you are recommended to turn off

the Bluetooth function of your mobile phone.