Справочник Пользователя для Ingersoll-Rand NP623XXXXR8-XX

Take note of the pump / drum clearance above. Be certain the 
lift / ram is clear of any objects above. Also, refer to “Operating 
and Safety Precautions” found on page 2 of RM052S-X Two Post 
Lift / Ram Operator’s Manual.
Connect the air supply (125 p.s.i. / 8.6 bar max.) to the air inlet. 
Adjust the air pressure on the lift / ram pressure regulator (turn 
the knob clockwise) to 20 p.s.i. (1.4 bar).
Shift the control valve lever to the “up” position.
Raise the lift / ram high enough to clear the height of the drum. 
Stop the lift upward travel by moving the control valve lever to 
the “neutral” (center) position.
Once the lift / ram assembly and pump are in the “up” position, 
place and center an opened drum of material on the lift / ram 
base.
Lubricate the lower follower wiper plate seal with grease. NOTE: 
Make certain the grease is compatible with the material being 
dispensed. This ensures a smooth fi t into the drum, as well as 
prevents curing type compounds from bonding to the seal.
Check the vent plug on the follower plate to be sure it easily 
threads in and out. It is recommended to lubricate the threads 
of the plug to help prevent possible set-up of the compound at 
this point (see RM052S-X Operator’s Manual).

causing injury. Keep hands clear when aligning with con-
tainer. Read the warnings on page 2 of RM052S-X Two Post Lift 
/ Ram Operator’s Manual.

NOTE: Be certain the follower plate vent plug has been removed 
so that the air trapped between the follower and the material is al-

1.

2.

3.
4.

5.

6.

7.

The NP623XXXXR8-XX Extrusion System comes completely assem-
bled. Remove the unit from the crate and place on a level surface. 
Install the material hose and dispensing device as required.
When the following instructions are observed, heavy paste materi-

als can be pumped directly from their original drum without air 
inclusion or excessive waste. The follower plate creates an air tight 
seal as well as clean-wiping action in its progressive downward 
movement into the drum.

lowed to escape from this vent.

NOTE: The lift / ram may hesitate momentarily before starting 
downward. The air pressure inside the post air chamber must de-
crease before it will begin to descend.

Shift the control valve lever to the “down” position and proceed 
to lower the pump.
Replace the vent plug once the material begins to ooze from 
the vent opening.
The unit is now ready for operation. Open the pump air supply 
valve. Adjust the air pressure on the pump fi lter / regulator (turn 
the pump regulator knob clockwise) until the pump begins to 
cycle.
Trigger the gun to prime the pump with material.

Close the pump air supply valve.
Shift the control valve lever to the “up” position.
Raise the lift / ram high enough to clear the height of the drum. 
Stop the lift upward travel by moving the control valve lever to 
the “neutral” (center) position.

TO CHANGE THE DRUM:
NOTE: The control valve lever must be in the “neutral” position and 
the pump air supply valve should be closed.

To avoid damage, DO NOT OVER PRESSURIZE THE DRUM.
Open the follower plate air supply valve to allow air under the 
follower plate.
Shift the control valve lever to the “up” position.
Place and center a new drum into position. Remove the cover.

1.

2.

3.

4.

1.
2.
3.

1.
2.

3.
4.

y ARO® is a registered trademark of Ingersoll-Rand Company y

 Stand clear when raising or lowering the lift. 

Read the warnings on page 2 of RM052S-X Two Post Lift / Ram 
Operator’s Manual.

OFF

OFF

ON

ON