Листовка для American Standard 621.001
SAVE FOR FUTURE USE
7 3 0 1 2 4 4 - 1 0 0 R e v . A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 9
© A S A m e r i c a , I n c . 2 0 0 9
NOTE: Pictures may not exactly define contour of china and components.
ABOVE COUNTER SINK FOR USE WITH: 0621.001 STUDIO
COUNTERTOP INSTALLATION
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Channel Lock Pliers
Jig Saw
Hacksaw
Phillips Screwdriver
Pipe Wrench
Basin Wrench
Drill
Tubing Cutter
Tape Measure
Silicone Adhesive
Plumber’s Putty or Caulking
RECOMMENDED FAUCET
*
: 2064.101 ONE lavatory faucet
*
Log on to www.americanstandard-us.com for additional faucet selections.
Connect supply line to
faucet (finger tight) and
carefully bend tubes to
engage with the supply
shut-off valves. Tighten
connections at faucet
and shut-off valves for
secure seal.
faucet (finger tight) and
carefully bend tubes to
engage with the supply
shut-off valves. Tighten
connections at faucet
and shut-off valves for
secure seal.
Mounting holes are provided on the rear of the
lavatory so it can be secured to the wall if desired.
lavatory so it can be secured to the wall if desired.
Shut-Off Valves
B
C
Connect trap to drain
assembly hand tight to
check alignment. It may
be necessary to cut off
part of the tailpiece (area
“B”) or part of the
horizontal leg of the trap
(area “C”). Secure joints
for watertight assembly.
assembly hand tight to
check alignment. It may
be necessary to cut off
part of the tailpiece (area
“B”) or part of the
horizontal leg of the trap
(area “C”). Secure joints
for watertight assembly.
Using the template provided, locate the position of the sink
on the countertop. Provide proper clearance under the
countertop for the faucet supply lines, drain assembly and
the structural parts of the cabinet.
on the countertop. Provide proper clearance under the
countertop for the faucet supply lines, drain assembly and
the structural parts of the cabinet.
NOTE: If replacing an existing sink be certain to shut off
water supply before removing old sink.
water supply before removing old sink.
1
4
• Place the sink temporarily into the template.
• Check for alignment and clearance.
• Mark the sink and countertop in several places
as a guide for the installation location.
as a guide for the installation location.
Mount the faucet and drain
assembly (not included) on
the sink following the
manufacturer’s instructions.
Be certain to apply a bead
of sealing putty on the
underside of the drain (Part
“A”) in order to ensure a
watertight seal between the
sink and drain. Remove
excess putty after installing
drain on sink.
assembly (not included) on
the sink following the
manufacturer’s instructions.
Be certain to apply a bead
of sealing putty on the
underside of the drain (Part
“A”) in order to ensure a
watertight seal between the
sink and drain. Remove
excess putty after installing
drain on sink.
3
A
Drill a clearance hole inside the perimeter line of the
template for countertop installation.
template for countertop installation.
Cut opening around the perimeter of the template.
2
Perimeter
of
template
Perimeter of
template
5
6
7
8
After checking fit
and alignment,
turn sink upside
down and apply a
generous portion
of silicone
adhesive around
the under side of
the rim near the
edge. Place sink in
position. Wipe off
excess adhesive.
and alignment,
turn sink upside
down and apply a
generous portion
of silicone
adhesive around
the under side of
the rim near the
edge. Place sink in
position. Wipe off
excess adhesive.