Справочник Пользователя для American Standard 2369
7 3 0 5 2 9 - 10 0 Rev. U
- 3 -
9a
Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
These parts must be used as illustrated
to insure water-tight connection. Use of
existing coupling nut may result in water
leakage. Water supply tube or pipe
must extend at least 1/2" inside
threaded shank of valve (does not apply
to flanged tubing).
to insure water-tight connection. Use of
existing coupling nut may result in water
leakage. Water supply tube or pipe
must extend at least 1/2" inside
threaded shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
coupling nut
and washer.
Use existing spiral cone
washer. Fluidmaster
cone washer may not
seal completely on
spiral type supply line.
washer. Fluidmaster
cone washer may not
seal completely on
spiral type supply line.
Captive cone
washers already
included. No
additional washers
needed.
washers already
included. No
additional washers
needed.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
NUT
COUPLING
NUT
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
COUPLING
NUT
NUT
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
CONE
WASHER
WASHER
EXISTING
CONE
WASHER
CONE
WASHER
EXISTING
WASHER
WASHER
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
!
WARNING: Do not use plumber’s putty, pipe dope, or any other sealant on the water supply
connection to this tank. If the connection leaks after hand tightening, replace the supply line.
If the connection continues to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.
connection to this tank. If the connection leaks after hand tightening, replace the supply line.
If the connection continues to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.
6
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers.
(If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
(If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
!
CLOSET BOLT
NUT
WASHER
BOLT CAP
INSTALL TANK
Recommended tool: Deep socket tool included in tank kit.
a. Install large rubber gasket over threaded outlet on bottom of tank and
lower tank onto bowl so that tapered end of gasket fits evenly into
bowl water inlet opening, and tank mounting bolts go through
mounting holes. Secure with metal washer/nuts. Use the included
deep socket tool to help get nuts started on bolts.
bowl water inlet opening, and tank mounting bolts go through
mounting holes. Secure with metal washer/nuts. Use the included
deep socket tool to help get nuts started on bolts.
b. With tank parallel to wall, alternately tighten hex nuts keeping tank
even and level until tank contacts both front and rear bowl mounting
ribs. Do not tighten any further.
ribs. Do not tighten any further.
CAUTION:
7
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
DO NOT SPIN BOLTS INSIDE TANK WITH A SCREWDRIVER
DO NOT SPIN BOLTS INSIDE TANK WITH A SCREWDRIVER
CLOSET FLANGE
!
WASHER/NUT
DEEP SOCKET
TOOL
TOOL
SCREWDRIVER
RUBBER
GASKET
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
BOLTS PRE-
INSTALLED
WASHER/NUT
SCREWDRIVER
DEEP
SOCKET
TOOL
MTG.
RIBS
RIBS