Справочник Пользователя для ONKYO HT-RC370
41
En
You can display various information about the current
input source as follows. (Components connected to the
UNIVERSAL PORT jack are excluded.)
input source as follows. (Components connected to the
UNIVERSAL PORT jack are excluded.)
The following information can typically be displayed.
Tip
• Alternatively, you can use the AV receiver’s DISPLAY.
*1
If the input signal is analog, “Analog” is displayed. If the
input signal is PCM, the sampling frequency is displayed. If
the input signal is digital but not PCM, the signal format is
displayed. Information is displayed for about three seconds,
then the previously displayed information reappears.
input signal is PCM, the sampling frequency is displayed. If
the input signal is digital but not PCM, the signal format is
displayed. Information is displayed for about three seconds,
then the previously displayed information reappears.
When you connect an
u-capable Onkyo component, you
must configure the input display so that
u can work
properly.
This setting can be done only from the front panel.
This setting can be done only from the front panel.
You can set which speakers you want to use by priority.
Note
• If the “Speakers Type(Front)” setting is set to “Bi-Amp”
page 46), or the “Powered Zone 2” is set to “Yes”
page 46), this setting cannot be selected.
• Playback conditions may be limited depending on the settings in
page 46).
• When a listening mode which doesn’t support front high, front
wide or surround back speakers is used, this setting cannot be
selected.
selected.
You can temporarily mute the output of the AV receiver.
Displaying Source Information
1
Press
RECEIVER followed by DISPLAY
repeatedly to cycle through the available
information.
information.
Changing the Input Display
1
Press
TV/CD, GAME or VCR/DVR.
“TV/CD”, “GAME” or “VCR/DVR” appears on the
display.
display.
2
Press and hold down
TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select the desired input display.
Repeat this step to select the desired input display.
Note
• DOCK can be selected for the TV/CD, GAME or
VCR/DVR input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (
Input source
Input signal
resolution
Output
resolution
Signal format
*1
Listening mode
Sampling
frequency
TV/CD
→
DOCK
→
→
TAPE
■
TV/CD:
TV/CD
→
DOCK
→
→
TAPE
GAME
↔ DOCK
■
GAME:
VCR/DVR
↔ DOCK
■
VCR/DVR:
Selecting Speaker Layout
1
Press
RECEIVER followed by SP LAYOUT
repeatedly.
`
Speaker Layout:FH:
The sound from front high speakers is output by
priority.
priority.
`
Speaker Layout:FW:
The sound from front wide speakers is output
by priority.
by priority.
`
Speaker Layout:SB:
The sound from surround back speakers is
output by priority.
output by priority.
Muting the AV Receiver
1
Press
RECEIVER followed by MUTING.
The output is muted and the MUTING indicator
flashes on the display.
flashes on the display.
Tip
• To unmute, press MUTING again or adjust the volume.
• Muting is automatically cancelled when the AV receiver is
• Muting is automatically cancelled when the AV receiver is
set to standby.
Using Headphones
1
Connect a pair of stereo headphones with a
standard plug (1/4 inch or 6.3 mm) to the
PHONES jack.
standard plug (1/4 inch or 6.3 mm) to the
PHONES jack.
Note
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers are turned off. (The Powered Zone 2
speakers are not turned off.)
speakers are not turned off.)
• When you connect a pair of headphones, the listening mode
is set to Stereo, unless it’s already set to Stereo, Mono,
Direct, or Pure Audio.
Direct, or Pure Audio.
• If you connect an iPod or iPhone to the USB port on this
device, no sound will be output from the headphones jack.