Справочник Пользователя для ONKYO HT-RC370
63
En
■
Operating on the AV receiver
■
Operating on the remote controller
To control Zone 2, you must press ZONE2 on the remote
controller first.
controller first.
Adjusting the Volume for Zone 2
■
Operating on the remote controller
■
Operating on the AV receiver
If your Zone 2 speakers are connected to a receiver or
integrated amp in Zone 2, use its volume control to adjust
the volume.
integrated amp in Zone 2, use its volume control to adjust
the volume.
Muting Zone 2
■
Operating on the remote controller
Tip
• To unmute, press ZONE2 followed by MUTING again.
Note
• Only analog input sources are output from the ZONE 2 LINE
OUT L/R jacks and FRONT WIDE/ZONE 2 L/R terminals.
Digital input sources are not output. If no sound is heard when
an input source is selected, verify that the source is connected to
an analog input.
Digital input sources are not output. If no sound is heard when
an input source is selected, verify that the source is connected to
an analog input.
• While Zone 2 is on,
u functions will not work.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same AM/FM radio station will be
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2.
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2.
• When you have selected NET or USB as the input selector, the
last selector selected will be set for both Main room and Zone 2.
• Zone 2 can also be unmuted by adjusting the volume.
• When Zone 2 is activated and its input selector is selected, the
• When Zone 2 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
• When setting the AV receiver to standby mode while Zone 2 is
active, the Z2 indicator is dimly lit.
• Activating Zone 2 in the main room when the listening mode is
set to Pure Audio will automatically switch it to Direct.
• AUX cannot be selected as the input selector for Zone 2.
• When AUX is the input source of Main room and Zone 2 is set
• When AUX is the input source of Main room and Zone 2 is set
to share the same source, no sound will be output from Zone 2.
Controlling Zone 2 Components
1
To turn on Zone 2 and select an input source, press
ZONE 2 followed by an input selector button
within 8 seconds.
ZONE 2 followed by an input selector button
within 8 seconds.
Zone 2 turns on, the Z2 indicator lights on the
display.
display.
To select AM or FM, press the TUNER input selector
button repeatedly.
button repeatedly.
To select the same source as the main room’s, press
ZONE 2 repeatedly until “Z2 Selector: Source”
appears on the display.
ZONE 2 repeatedly until “Z2 Selector: Source”
appears on the display.
To turn off Zone 2, press
OFF.
The zone is turned off.
1
Press
ZONE2 and then press
8RECEIVER.
Zone 2 turns on, the Z2 indicator lights on the
display.
display.
2
To select an input source for Zone 2, press
ZONE2,
followed by an input selector button.
To select AM or FM, press the TUNER input selector
repeatedly.
To select AM or FM, press the TUNER input selector
repeatedly.
Note
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same AM/FM radio
station will be heard in each room.
station will be heard in each room.
3
To turn off Zone 2, press
ZONE2 followed by
8RECEIVER.
ZONE 2 OFF
MASTER VOLUME
Input selector buttons
8RECEIVER
MUTING
VOL
q/w
ZONE2
Input selector buttons
1
Press
ZONE2.
2
Use
VOL
q/w to adjust the volume.
1
Press
ZONE 2 (the Z2 indicator on the display
flash).
2
Use
MASTER VOLUME control within 8 seconds
to adjust the volume.
1
Press
ZONE2 followed by MUTING.