Справочник Пользователя для Marantz SR4001

This function allows the component connected to the 
TV-VIDEO in jack to control the power (ON/OFF) to 
the SR4001/SR5001.

 

  Be sure the TV auto mode is ENABLED. (Refer 

page 27 : System Setup)

 

  Connect your TV TUNER (etc) to the TV-

VIDEO in terminal. Be sure to connect the 
VIDEO input.

 

  Turn OFF the power to the TV TUNER and the 

SR4001/SR5001.

 

  Turn ON the TV TUNER and tune in a receivable 

station.

 

  When the station is received, the SR4001/

SR5001 turns ON and TV is selected 
automatically.

 

  In the above situation, turn the TV TUNER OFF 

or select a channel that does not contain any 
broadcast.

 

  The power to the SR4001/SR5001 switches to 

STANDBY after approx. 5 minutes.

• AUTO POWER OFF is canceled if the SR4001/

SR5001 is set to a source other than TV. 

  The function reactivates when TV is selected again.

• Some TV broadcasts may cause the TV AUTO 

FUNCTION to turn ON.

•  The S-Video terminal does not support “TV AUTO 

ON/OFF” function.

If the selected analog audio input signal is greater 
than the capable level of internal processing, the 
“

” indicator will light up on the front display. If 

this happens, you should press the 

 button on 

the remote.
“

” indicator will be illuminated when this function 

is activated. The signal-input level is reduced by 
about half. Attenuation will not work with the output 
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT 
and DSS/VCR2-OUT. 
This function is memorized for each individual input 
source.

This jack may be used to listen to the SR4001/
SR5001’s output through a pair of headphones. 
Be certain that the headphones have a standard 
1/4” stereo phono plug. (Note that the speakers will 
automatically be turned off when the headphone jack 
is in use.)

The surround mode returns to the previous setting as 
soon as the plug is removed from the jack.

This feature simulates the waveforms of the actual 
sounds heard from the speakers.
When headphones are used, the 

 button 

automatically switches to the Dolby headphone 
mode.
The OSD that appears when the 

 button is 

pressed is shown below.

     HEAD PHONE

DOLBY HP MODE : ON
SURROUND      : OFF

L LEVEL       :   0 dB
R LEVEL       :   0 dB

DOLDBY HP (Headphone) MODE can be selected 
with the left and right cursor buttons.
BYPASS 

→

 ON 

→

 BYPASS

 BYPASS:  Bypasses the Dolby headphone mode 

and delivers ordinary 2-channel stereo.

 

ON:  Dolby headphone mode active.

When the PURE DIRECT mode is selected, Dolby 
surround processing is bypassed and “

✽✽✽

” is 

displayed as the mode indication.

The surround mode can be selected when mode is 
ON.

L/R LEVEL can be set in the ±10 dB range.

•  The surround mode returns to the previous setting as 

soon as the plug is removed from the jack.

•  TONE cannot be set when mode is ON.

•  The Dolby Headphone function will not work when 

32 or 96 kHz PCM digital signals are input.

When no video signal is connected to the SR4001/
SR5001 or a DVD, etc., is connected directly to your 
TV, the unnecessary video circuit can be turned off 
by selecting the “

” setting.

To select video off, press the 

 button and press 

the 

 button. 

You can select the display mode for the front display 
of the SR4001/SR5001.
To select this mode, press the 

 on the 

remote control.
When this button is pressed, the display mode is 
switched in the following sequence.

→

 Surround Mode 

→

 Auto-display Off 

→

 Display Off 

→

 Input Function 

→

 Surround Mode....

In Auto display off mode, the display is off. But, if you 
make a change to the unit such as input or surround 
mode, the display will show that change, then go 
back to off after about 3 seconds. When changing the 
volume, it is not displayed.
In Display off mode, the display is off completely.

Only the DISP indicator will be illuminated on the 
front display in display off condition