Справочник Пользователя для Marantz SR4021
10
ENGLISH
CONNECTING VIDEO COMPONENTS
IN
PHONO
IN
IN
OUT
IN
OUT
DSS
AUX
VIDEO
CONTROL
REMOTE
GND
VCR
IN
OU
L
IN
OUT
IN
OUT
OUT
IN
IN
IN
OUT
IN
(CD-R)
(TAPE)
AUX
CD
DSS
PRE
DVD
RECORDER 2
MAIN
VCR
RECORDER 1
IN
DVD
AUDIO
R
MONITOR
MODEL NO.
IN
IN
AM
FM (75 )
GND
ANTENNA
AUDIO
IN
IN
OUT
IN
DSS
AUX
DVD
VCR
IN
IN
IN
OUT
IN
DSS
VCR
DVD
MONITOR
VIDEO
OUT
OUT
OUT
L
VIDEO
R
VIDEO
IN
CVBS
L R
AUDIO
OUT
VIDEO
OUT
L R
AUDIO
OUT
AUDIO
IN
L R
VIDEO
OUT IN
L R
AUDIO
OUT
VIDEO
OUT
L R
L R
L R
L
R
L
R
L R
L R
L R
L R
L
R
VCR
Monitor
DVD player
Satellite tuner
VIDEO camera etc..
Notes:
• Insert all plugs and connectors securely. Incomplete connections will result in the generation of noise.
• Be sure to connect the left and right channels properly.
Red connectors are used for the R (right) channel, and white connectors are used for L (left) channel.
• Be sure to connect input and output of video signal properly.
• Be sure to connect the left and right channels properly.
Red connectors are used for the R (right) channel, and white connectors are used for L (left) channel.
• Be sure to connect input and output of video signal properly.
CONNECTING THE REMOTE CONTROL JACKS
IN
PHONO
IN
IN
OUT
IN
OUT
DSS
AUX
VIDEO
CONTROL
REMOTE
GND
VCR
IN
OUT
L
IN
OUT
IN
OUT
OUT
IN
IN
IN
OUT
IN
(CD-R)
(TAPE)
AUX
CD
DSS
PRE
DVD
RECORDER 2
MAIN
VCR
RECORDER 1
IN
DVD
AUDIO
R
MONITOR
IN
IN
AM
FM (75 )
GND
ANTENNA
OUT
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
OPEN/CLOSE
FL OFF
VIRTUAL
STANDBY
POWER ON/STANDBY
DVD PLAYER DV4600
CD player
CD recorder
DVD player
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then the
signal is sent to the connected device through this
terminal. Therefore you only need to aim the remote
at one unit. Also, if a Marantz power amplifi er (some
models excluded) is connected to one of these
terminals, the power amplifier’s, power switch is
synchronized with this unit’s power switch.
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then the
signal is sent to the connected device through this
terminal. Therefore you only need to aim the remote
at one unit. Also, if a Marantz power amplifi er (some
models excluded) is connected to one of these
terminals, the power amplifier’s, power switch is
synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for this
feature.
other than the main unit to EXT.(EXTERNAL) for this
feature.
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR4021,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR4021,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1.
Hold
down the SLEEP button and DIMMER
button on the front panel at the same time for 3
seconds.
seconds.
2.
The
setting “IR=ON” is shown on the FL
DISPLAY.
3.
Turn the MULTI JOG knob to change this to
“IR=OFF”.
4.
Press the MEMORY button. Once this setting
is made, the infrared sensor on the main unit is
disabled.
disabled.
Note:
Be sure to set to “IR=ON” when external infrared
sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
Otherwise, the main unit will be unable to receive
remote control commands.
5.
To
restore the original setting, perform steps 1
to 4 to set to “IR=ON”.