Справочник Пользователя для Marantz SR8000

14

To select the tuner as the source, press the 

button t on

the front panel or press the 

button . on the remote.

Press the 

button t on the front panel or press the

button . on the remote to select the desired frequency

band if required.

Press the 

 button !6 on the front panel to display the frequency.

Press the 

   or   button !5 on the front panel or

press the 

1, ¡ button ⁄5 on the remote.

If FM is selected, press the 

button !7 on the front panel or

the 

button D5 on the remote to select the desired audio

mode.

When “AUTO” indicator is on in the display, FM stations that
broadcast in stereo will be received in stereo and the “STEREO”
indicator lights.
When “AUTO” indicator is off, all the FM stations will be received in
mono regardless of whether or not they are broadcasting in stereo.

Press the 

 button !6 on the front panel to display the frequency.

Press the 

   or   button !5 on the front panel

for more than 1 second to start the Auto tuning function.

Press 

1  or ¡ button for more than 1 second to start the Auto

tuning function.

With this unit you can preset up to 50 FM/AM stations in any order. For
each station, you can memorize the frequency and reception mode if
desired.

Refer to the “MANUAL TUNING” or “AUTO TUNING” section
above to tune in a desired station.

Press the 

button !4. “MEMO” indicator starts blinking

on the display.
While “MEMO” is still blinking (approx. 5 seconds), select the
preset number by pressing the 

   or   button

!5  then press the 

button !4 again.

When a number has been properly input, “MEMO” indicator
stops blinking and goes out.
The station is now stored in the specified preset memory location.

Tune in a desired station.

Press the 

button ⁄3.

Enter the desired preset number with ten keypad ⁄2.

* When entering a single digit number (2, for example), either input
“02” or just input “2” and wait for a few seconds.
* If a number other than 1-50 is entered by mistake, that number
flashes in the display to indicate that it is invalid and the display
returns to the original frequency display.

This function automatically scans the AM and FM band and enters all
stations with sufficient signal strength into the memory.
This function is available only for SR8000.

Select the FM band with the 

button on the remote.

Tune in the lowest receivable frequency.

While pressing the 

button !4, press the 

 button !5 .  Auto memory starts at this point.

“MEMO “ will blink on the display.

Each time the tuner finds a station, the scanning will pause and
the station will be played for five seconds. During this time, the
following operations are possible:

1) The band can be changed using the 

button on the

remote.

2) The mode can be changed using the (FM) 

button !7 .

If no button is pressed during this period, the current frequency is
preset in location CH-2.
If you wish to skip the current station, press the 

 

or   button !5 during this period, the current frequency is skipped
and auto presetting continues.

Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the 

button !3.

Press the

 button !6 to change the display to preset.

Select the desired preset station by pressing 

 or   button !5 on the front panel or press 

4 or ¢  button ⁄5

on the remote.

To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits
using the numeric keypad  ⁄5.
To return to the Manual Tuning mode, press the 

 button !6.

Press the 

(preset scan) button D8 on the remote. “P-

SCAN” indicator blinks in the display. (The preset station with the
smallest preset number is recalled first. If no stations have been
preset, CH “00” blinks in the display and the unit returns to the
previous mode.)

Preset stations are recalled in sequence (CH-1 

→

 CH-2, etc.) for

5 seconds each. Preset numbers that do not contain stations are
skipped.

You can fast forward the preset stations by pressing the 

¢

button continuously.
When the desired preset station is received, cancel the preset
scan operation by pressing the 

4 button or the SCAN button

D8 or 

button !3.

You can remove preset stations from memory using the following
procedure.

Recall the preset number to be cleared with the method
described in “Recalling” a preset station .

Press the 

button !4 on the front panel or 

(MEMO)

button ⁄3 on the remote unit, “MEMO” blinks in the display for 5
seconds.  While “MEMO” is still blinking, press the 

button

!3 on the front panel or 

(CLEAR) button ⁄4 on the remote unit.

“CLEAR” appears on the display to indicate that the specified
preset number has been cleared.