Справочник Пользователя для Hifionics ZRX1000.1D
AMPLIFIER FEATURE DESCRIPTIONS
ZEUS ZRX AMPLIFIERS:
2
ZRX1000.1D / ZRX1500.1D / ZRX2000.1D / ZRX3000.1D 1-CHANNEL AMPLIFIERS
The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a Mode switch. Switch to 2 channel if you only have 1 set of
RCA’s in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 3 channel if you
are running stereo on ch 1&2 and mono on ch 3&4. Select 4 channel if you are providing RCA’s to
channels 1/2 and 3/4.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a Mode switch. Switch to 2 channel if you only have 1 set of
RCA’s in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 3 channel if you
are running stereo on ch 1&2 and mono on ch 3&4. Select 4 channel if you are providing RCA’s to
channels 1/2 and 3/4.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 12dB.
Note that the LOW PASS signal is MONO.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
ZRX600.4 / ZRX1000.4 / ZRX2000.4 4-CHANNEL AMPLIFIERS
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30Hz to 250Hz.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 12dB.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30Hz to 250Hz.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 12dB.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
Note that the LOW PASS signal is MONO.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
ZRX500.2 / ZRX1200.2 2-CHANNEL AMPLIFIERS
POWER
LEVEL BASS EQ REMOTE SUBSONIC LOW PASS
PROTECT
OUTPUT
INPUT
L
R
L
R
6V 0.2V 0dB 10dB 15HZ 35HZ 30HZ 250HZ
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU
Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
the mono amps which are capable of 4, 2 and 1-Ohm loads.
WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4
The input sensitivities for rated output powers are variable from 0.2V to 6V.
and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2
All crossovers are fully variable in their respective ranges.
and 1-Ohm.
Crossover filters are 12dB/Octave.
A POWER LED indicates the powered up and turned on condition.
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
and amplifier DC faults indicated by the red “PROTECT” LED.
A POWER LED indicates the powered up and turned on condition.
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
and amplifier DC faults indicated by the red “PROTECT” LED.
POWER
LEVEL BASS EQ X-OVER HPF LPF MODE
PROTECT
OUTPUT
INPUT
L
R
L
R
6V 0.2V 0dB 12dB 60HZ 13KHZ 30HZ 250HZ
FULL
MONO
HPF
STEREO
LPF
POWER
LEVEL BASS EQ X-OVER HPF LPF
CH 3 / 4
CH 1 / 2
LEVEL BASS EQ X-OVER HPF LPF MODE
PROTECT
CH 1 / 2
CH 3 / 4
R
L
LINE OUT
R
L
6V 0.2V 0dB 12dB 60HZ 13KHZ 30HZ 250HZ
6V 0.2V 0dB 12dB 60HZ 13KHZ 30HZ 250HZ
FULL
FULL
2 3 4
HPF
HPF
LPF
LPF
-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER
setting simplifying daisy chaining of amplifiers.
-SUBSONIC: Allows you to adjust the crossover filter from 15Hz to 35Hz.
-LOW PASS: Allows you to adjust the LOW PASS crossover filter from 30Hz to 250Hz.
LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.
BASS EQ: The Bass EQ is adjustable from 0db to 10dB.
REMOTE: This is the input jack for the remote Level control.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
setting simplifying daisy chaining of amplifiers.
-SUBSONIC: Allows you to adjust the crossover filter from 15Hz to 35Hz.
-LOW PASS: Allows you to adjust the LOW PASS crossover filter from 30Hz to 250Hz.
LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.
BASS EQ: The Bass EQ is adjustable from 0db to 10dB.
REMOTE: This is the input jack for the remote Level control.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.