Справочник Пользователя для Marantz SR5600

If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio
source to AUX2 as other audio input terminals.

Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5600, a time
lag can occur between image signal processing
and audio signal processing. Though minor, this
time lag can interfere with movie and music
enjoyment. The LIP.SYNC feature delays the
audio signal with respect to the image signal
output from the SR5600 to correct the time lag
between the sound and image. It can be operated
with the “LIP.SYNC” and   and   cursor buttons of
the remote controller. Set the remote controller to
the AMP mode before operating the LIP.SYNC
feature. The initial setting is OFF (0 ms).The time
lag can be adjusted in 10 ms steps up to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.

• The LIP.SYSNC feature turns OFF (0 ms) in the

PURE DIRECT mode. When the PURE DIRECT
mode is deactivated, the set value of the
LIP.SYSNC feature is automatically restored.

Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s
standard is 9 kHz step, Press 

button on

the remote more than 6 seconds. Scan step will
change.

• Preset memory for the tuner will clear by changing

this setup.

To select tuner and desired band (FM or AM),
press the 

button on the front panel.

Press the

 or   cursor buttons on the front

panel for more than 1 second to start the auto
tuning function.

Automatic searching begins then stops when
a station is tuned in.

To select tuner and desired band (FM or AM),
press the 

button twice within in two

seconds on the remote.

Press the 

5

5

5

5

5

 or 

6

6

6

6

6

for more than 1 second on

the remote.

Automatic searching begins then stops when
a station is tuned in.

If tuning does not stop at the desired station, use to
the “Manual tuning” operation.

To select tuner and desired band (FM or AM),
press the 

button on the front panel

Press the

 or   cursor buttons on the front

panel to select the desired station.

To select tuner and desired band (FM or AM),
press the 

button twice within in two

seconds on the remote.

Press the 

5

5

5

5

5

 or 

6

6

6

6

6 

on the remote

to tune in the

desired station.

To select tuner and desired band (FM or AM),
press the 

button twice within two

seconds on the remote.

Press the 

on the remote, display

will show “

”.

Input your desired station’s frequency with the

 buttons on the remote.

The desired station will automatically be
tuned.

Select a desired Video source to decide the
routed video signal to the 

Press the 

 button on the front

panel or press 

on the remote to

switch the 7.1 channel input.

If it is necessary to adjust the output level of
each channel, press the 

 button on

the remote.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.

Adjust the main volume with the 

 knob or the 

 buttons on the

remote.

To cancel the 7.1 CH. INPUT setting, press the 

 button on the front panel or press 

on the remote.

• When the 7.1 CH. Input is in use, you may not

select a surround mode, as the external decoder
determines processing.

• In addition, there is no signal at the record outputs

when the 7.1 CH. Input is in use.

0

AAC

0

AAC

3

2

1

6

5

4

9

8

0

7

SR5600U DFU_01_ENG 2_2

05.6.3, 3:44 PM

Page 29

Adobe PageMaker 6.5J/PPC