Справочник Пользователя для Peavey SSE UB2T
suspended, resulting in serious injury and
property damage. DO NOT suspend or
mount any other product or device from
this enclosure. Use only the correct mating
hardware. All associated rigging is the
responsibility of others. This unit was
designed to be hung on the wall or ceiling
with the use of a special bracket that fits
into the enclosure, via a slot on the rear,
and an insert located on the top rear of the
cabinet. Use only the supplied bracket.
property damage. DO NOT suspend or
mount any other product or device from
this enclosure. Use only the correct mating
hardware. All associated rigging is the
responsibility of others. This unit was
designed to be hung on the wall or ceiling
with the use of a special bracket that fits
into the enclosure, via a slot on the rear,
and an insert located on the top rear of the
cabinet. Use only the supplied bracket.
Architectural & Engineering
Specifications
The loudspeaker system shall have an
operating bandwidth of 160 Hz to 16 kHz
with signal processing, using the 8 ohm
input. The nominal output level shall be
90 dB when measured at a distance of one
meter with an input of one watt into the 8
ohm input, where the nominal impedance
shall be 8 ohms. A 70V/100V distributed
line transformer shall be included, with
a selector switch to select between
transformer taps of: 30W, 15W, 7.5W, 3.7W,
1.8W or to an 8 ohm nominal input. The
maximum continuous power handling shall
be 50 watts, maximum program power of
100 watts and a peak power input of at
least 200 watts, with a minimum amplifier
headroom of 3 dB, for the 8 ohm input. The
transformer input maximum continuous
power handling shall be 30W, with a
maximum peak power of 60W, for either
a 100V or 70V input line. The nominal
radiation geometry shall be 180 degrees
in the horizontal plane and 90 degrees
in the vertical plane. The overall outside
dimensions shall be 3.23 inches high by
13.78 inches wide by 6.12 inches deep. The
weight shall be 5 pounds. The mounting/
flying bracket shall be included with the
unit. The loudspeaker system shall be a
Peavey Sanctuary Series model SSE
operating bandwidth of 160 Hz to 16 kHz
with signal processing, using the 8 ohm
input. The nominal output level shall be
90 dB when measured at a distance of one
meter with an input of one watt into the 8
ohm input, where the nominal impedance
shall be 8 ohms. A 70V/100V distributed
line transformer shall be included, with
a selector switch to select between
transformer taps of: 30W, 15W, 7.5W, 3.7W,
1.8W or to an 8 ohm nominal input. The
maximum continuous power handling shall
be 50 watts, maximum program power of
100 watts and a peak power input of at
least 200 watts, with a minimum amplifier
headroom of 3 dB, for the 8 ohm input. The
transformer input maximum continuous
power handling shall be 30W, with a
maximum peak power of 60W, for either
a 100V or 70V input line. The nominal
radiation geometry shall be 180 degrees
in the horizontal plane and 90 degrees
in the vertical plane. The overall outside
dimensions shall be 3.23 inches high by
13.78 inches wide by 6.12 inches deep. The
weight shall be 5 pounds. The mounting/
flying bracket shall be included with the
unit. The loudspeaker system shall be a
Peavey Sanctuary Series model SSE
UB2T.
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the warranty
statement. Copies of this statement may be
obtained by contacting Peavey Electronics
Corporation, P.O. Box 2898, Meridian,
Mississippi, 39301-2898.
statement. Copies of this statement may be
obtained by contacting Peavey Electronics
Corporation, P.O. Box 2898, Meridian,
Mississippi, 39301-2898.
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
60
70
80
90
100
110
dB
SPL
(re
20
Pa)
Amplitude Response (1m Equivalent On-Axis)
W/ woofer
SSE- UB2
HF Only vs System
Figure 1
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
1
2
3
5
10
20
30
50
100
Impedance
Z
( )
Figure 2
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
30
40
60
80
100
140
180
300
360
Beam
w
id
th
(Degrees
)
Beamwidth
Vertical
Horizontal
Figure 3
SPECIFICATIONS
SSE
™
UB2T
3