Справочник Пользователя для Mitsubishi Electronics MR-J2S- CP
14 - 34
14. OPTIONS AND AUXILIARY EQUIPMENT
14.2 Auxiliary equipment
Always use the devices indicated in this section or equivalent. To comply with the EN Standard or UL/C-
UL (CSA) Standard, use the products which conform to the corresponding standard.
14.2.1 Recommended wires
UL (CSA) Standard, use the products which conform to the corresponding standard.
14.2.1 Recommended wires
(1) Wires for power supply wiring
The following diagram shows the wires used for wiring. Use the wires given in this section or
equivalent.
equivalent.
C
P
U
V
W
L
11
L
21
B1
B2
U
V
W
L
1
L
2
L
3
Motor
Power regeneration
converter
converter
N
1) Main circuit power supply lead
Power supply
Servo amplifier
3) Motor power supply lead
Servo motor
Electro-
magnetic
brake
magnetic
brake
Encoder
Encoder cable (refer to section 14.1.4)
4) Regenerative option lead
5) Electromagnetic
brake lead
brake lead
2) Control power supply lead
Regenerative option
6) Power regeneration
converter lead
converter lead
The following table lists wire sizes. The wires used assume that they are 600V vinyl wires and the
wiring distance is 30m(98.4ft) max. If the wiring distance is over 30m(98.4ft), choose the wire size in
consideration of voltage drop.
The alphabets (a, b, c) in the table correspond to the crimping terminals (Table 14.2) used to wire the
servo amplifier. For connection with the terminal block TE2 of the MR-J2S-100CP or less, refer to
section 3.11.
The servo motor side connection method depends on the type and capacity of the servo motor. Refer to
section 3.8.
To comply with the UL/C-UL (CSA) Standard, use UL-recognized copper wires rated at 60 (140) or
more for wiring.
wiring distance is 30m(98.4ft) max. If the wiring distance is over 30m(98.4ft), choose the wire size in
consideration of voltage drop.
The alphabets (a, b, c) in the table correspond to the crimping terminals (Table 14.2) used to wire the
servo amplifier. For connection with the terminal block TE2 of the MR-J2S-100CP or less, refer to
section 3.11.
The servo motor side connection method depends on the type and capacity of the servo motor. Refer to
section 3.8.
To comply with the UL/C-UL (CSA) Standard, use UL-recognized copper wires rated at 60 (140) or
more for wiring.
Table 14.1 Recommended wires
(Note 1) Wires [mm
2
]
Servo amplifier
1) L
1
L
2
L
3
2)
L
11
L
21
3)
U V W
4)
P C 5)
B1 B2
MR-J2S-10CP(1)
MR-J2S-20CP(1)
MR-J2S-40CP(1)
MR-J2S-60CP
MR-J2S-70CP
MR-J2S-20CP(1)
MR-J2S-40CP(1)
MR-J2S-60CP
MR-J2S-70CP
1.25 (AWG16) : a
MR-J2S-100CP
2 (AWG14) : a
2 (AWG14) : a
MR-J2S-200CP
3.5 (AWG12) : b
3.5 (AWG12) : b
MR-J2S-350CP
(Note 2)
5.5 (AWG10) : b
5.5 (AWG10) : b
MR-J2S-500CP
5.5 (AWG10) : b
5.5 (AWG10) : b
2 (AWG14) : a
MR-J2S-700CP
8 (AWG8) : c
1.25 (AWG16)
8 (AWG8) : c
3.5(AW12) : c
1.25 (AWG16)
Note 1. For the crimping terminals and applicable tools, refer to table 14.2.
2. 3.5mm
2
for use of the HC-RFS203 servo motor.