Справочник Пользователя для Kathrein BAS 61
lf you wish to drive with your vehicle without the flat
antenna mounted, but the jointed mast still installed,
you should protect the antenna as shown in opposite
illustration.
antenna mounted, but the jointed mast still installed,
you should protect the antenna as shown in opposite
illustration.
•
Care for adequate insulation or sealing of the
antenna plug. Protect the plug from moisture.
antenna plug. Protect the plug from moisture.
•
Bend the antenna cable to the form of a loop and
introduce the end of the cable into the joint of the
mast until the plug has disappeared in the lower
part of the joint.
introduce the end of the cable into the joint of the
mast until the plug has disappeared in the lower
part of the joint.
Then check if the mobile antenna support is well
fixed. lf necessary, tighten the two socket head
screws of the bracket.
fixed. lf necessary, tighten the two socket head
screws of the bracket.
•
Place the flat antenna evenly on an appropriate
support.
support.
•
Place the washers on the socket head screws and
screw the antenna support to the back of the flat
antenna (see opposite illustration). Use for that
purpose the 4 socket head screws belonging to
the mobile antenna support.
screw the antenna support to the back of the flat
antenna (see opposite illustration). Use for that
purpose the 4 socket head screws belonging to
the mobile antenna support.
•
Now screw in with your fingers the 4 socket head
screws. Pay attention that they are not twisted and
damage the thread.
screws. Pay attention that they are not twisted and
damage the thread.
•
When positioning the antenna support, make sure
that the socket head screws are positioned exactly
in the middle of the elongated holes. Then take the
short shaft of an Allen key in your hand and screw
the socket head screws tight. See opposite
illustration.
that the socket head screws are positioned exactly
in the middle of the elongated holes. Then take the
short shaft of an Allen key in your hand and screw
the socket head screws tight. See opposite
illustration.
•
Then tighten the socket head screws with a torque
spanner. The torque moment is 6.5 Nm. lf no
torque spanner is available, the following method
will do: Take the long shaft of the Allen key in your
hand and tighten the socket head screws giving an
1/4 to an 1/2 turn.
spanner. The torque moment is 6.5 Nm. lf no
torque spanner is available, the following method
will do: Take the long shaft of the Allen key in your
hand and tighten the socket head screws giving an
1/4 to an 1/2 turn.
6. Notice regarding the polarisation setting
The polarisation setting is dependent on the geo-
graphic reception site. The annexed mounting
instructions „Flat antennas BAS 62 and BAS 63
for stationary use“ explain on page 4 how the
polarisation is set.
graphic reception site. The annexed mounting
instructions „Flat antennas BAS 62 and BAS 63
for stationary use“ explain on page 4 how the
polarisation is set.
4. Driving without the mounted flat antenna
5. Mounting the antenna support
Mobile antenna support
Joint
Driving direction
Cable binder
Cable plug
Take the long shaft of the
Allen key in your hand
and tighten the socket
head screws giving an
1/4 to an 1/2 turn.
Allen key in your hand
and tighten the socket
head screws giving an
1/4 to an 1/2 turn.
Take the short
shaft of the Allen
key in your hand
and screw the
hex. socket
screw tight.
The hex. socket head screw
must be positioned in the
middle of the elongated
hole of the antenna support
Flat antenna
4 hex. socket head screws
with washers
with washers
9985-551/798
/3.3e/H&S
Subject to technical changes!
Antenna support
KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 • Postfach 10 04 44 • D-83004 Rosenheim • Deutschland • Telefon (0 80 31) 18 40 • Fax (0 80 31) 18 43 06