Справочник Пользователя для Panasonic SC-MAX770

VQ
T

5K

75

Before requesting service, make the following checks.
If you are in doubt about some of the check points, or if 
the solutions indicated do not solve the problem, consult 
your dealer for instructions.

The unit does not work.
• One of the unit’s safety devices may have been 

activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to 

standby.
• If the unit does not switch to standby, press [Í/I] 

on the main unit for a few seconds. The unit is 
forcibly switched to standby. Alternatively, 
disconnect the AC power supply cord, wait one 
minute, then reconnect it.

2 Press [Í/I] on the main unit to switch it on. If the 

unit still cannot be operated, consult the dealer.

The display panel lights up and changes 
continuously in standby mode.
• Press and hold [∫] on the main unit to select “DEMO 

OFF”.

No operations can be done with the remote control.
• Examine that the battery is installed correctly.

Sound is distorted or no sound.
• Adjust the volume of the system.
• Switch off the system, determine and correct the 

cause, then switch the system on again. It can be 
caused by straining of the speakers through excessive 
volume or power, and when using the system in a hot 
environment.

A humming sound can be heard during playback.
• An AC power supply cord or fluorescent light is near 

the cables. Keep other appliances and cords away 
from the cables of this system.

The sound level reduces.
• The protection circuit has been activated due to the 

continuous use at high volume output. This is to 
protect the system and maintain the sound quality.

Display not shown correctly.
Playback does not start.
• You have not put in the disc correctly. Put it in correctly.
• Disc is dirty. Clean the disc.
• Replace the disc if it is scratched, warped, or 

non-standard.

• There is condensation. Let the system dry for 1 to 

2 hours.

The total number of tracks displayed is incorrect.
The disc cannot be read.
Distorted sound is heard.
• You put in a disc that the system cannot play. Change 

to a playable disc.

• You put in a disc that has not been finalized.

The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it 

is/are not compatible with the system.

• USB devices with storage capacity of more than 32 GB 

cannot work in some conditions.

Slow operation of the USB device.
• Large content size or large memory USB device takes 

longer time to read.

Sound is distorted.
• Use an optional FM outdoor antenna. The antenna 

should be installed by a competent technician.

A beat sound is heard.
• Switch off the TV or move it away from the system.
• When in AM tuner mode, select from “BP 1” to “BP 4” 

that provides the best reception.

A low hum is heard during AM broadcasts.
• Move the antenna away from other cables and cords.

Pairing cannot be done.
• Check the Bluetooth

®

 device condition.

The device cannot be connected.
• The pairing of the device was unsuccessful.

Do pairing again.

• The pairing of the device has been replaced.

Do pairing again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device 
again.

The device is connected but audio cannot be heard 
through the system.
• For some built-in Bluetooth

®

 devices, you have to set 

the audio output to “SC-MAX770” manually. Read the 
operating instructions of the device for details.

Sound from the device is interrupted.
• The device is out of the 10 m communication range.

Move the device nearer to the system.

• Remove any obstacle between the system and the 

device.

• Other devices that use the 2.4 GHz frequency band 

(wireless router, microwaves, cordless phones, etc.) 
are interfering. Move the device nearer to the system 
and distance it from the other devices.

• Select “MODE 1” for stable communication.

• Make sure the unit and the NFC feature of the device are turned 

on. (> 13)

SC-MAX770PU_eng.book  17 ページ  ２０１４年３月６日　木曜日　午後２時５４分