Справочник Пользователя для Milwaukee 9566

Milwaukee Electric Tool Corporation
13135 West Lisbon Road
Brookfield, Wisconsin 53005
TEL: (800) 729-3878

Each 

MILWAUKEE Electric Chain Hoist is built in accordance with

the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of
*American Society of Mechanical Engineers Code (ASME)
B30.16 “Overhead Hoists,” the National Electrical Code
(ANSI/NFPA 70) and the Occupational Safety and Health Act
(OSHA). Since OSHA states the National Electrical Code applies
to all electric hoists, installers are required to provide current
overload protection and grounding on the branch circuit section in
keeping with the code. Check each installation for compliance with
the application, operation and maintenance sections of these
articles.

*Copies of this standard can be obtained from ASME Order
Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300,
U.S.A.

1.

operate a damaged, malfunctioning or unusually 

performing hoist.

2.

operate the hoist until you have thoroughly read and

understood the manufacturer’s Operating and Maintenance
Instructions or Manuals.

3.

operate a hoist which has been modified without the

manufacturer’s approval or without certification that it is in
conformity with ANSI/ASME B30 volumes.

4.

lift more than rated load for the hoist.

5.

use hoist with twisted, kinked, damaged, or worn load

chain.

6.

use the hoist to lift, support, or transport people.

7.

lift loads over people.

8.

operate a hoist unless all persons are and remain clear

of the supported load.

9.

operate unless load is centered under hoist.

10.

attempt to lengthen the load chain or repair damaged 

load chain.

11. Protect the hoist’s load chain from weld splatter or other

damaging contaminants.

12.

operate hoist when it is restricted from forming a

straight line from hook to hook in the direction of loading.

13.

use load chain as a sling, or wrap chain around load.

14.

apply the load to the tip of the hook or to the hook latch.

15.

apply load unless load chain is properly seated in the 

chain sprocket(s).

16.

apply load if bearing prevents equal loading on all load

supporting chains.

17.

operate beyond the limits of the load chain travel.

18.

leave load supported by the hoist unattended unless

specific precautions have been taken.

19.

allow the load chain or hook to be used as an electrical

or welding ground.

20.

allow the load chain or hook to be touched by a live 

welding electrode.

21.

remove or obscure the warnings on the hoist.

22.

operate a hoist on which the safety placards or decals

are missing or illegible.

23.

operate a hoist unless it has been securely attached to

a suitable support.

24.

operate a hoist unless load slings or other approved

single attachments are properly sized and seated in the hook
saddle.

25. Take up slack carefully - make sure load is balanced and load

holding action is secure before continuing.

26. Shut down a hoist that malfunctions or performs unusually

and report such malfunction.

27. Make sure hoist limit switches function properly.

28. Warn personnel of an approaching load.

1. Maintain firm footing or be otherwise secured when operating 

the hoist.

2. Check brake function by tensioning the hoist prior to each 

lift operation.

3. Use hook latches. Latches are to retain slings, chains, etc.

under slack conditions only.

4. Make sure the hook latches are closed and not supporting

any parts of the load.

5. Make sure the load is free to move and will clear all

obstructions.

6. Avoid swinging the load or hook.

7. Make sure hook travel is in the same direction as shown on 

the controls.

8. Inspect the hoist regularly, replace damaged or worn parts,

and keep appropriate records of maintenance.

9. Use 

MILWAUKEE recommended parts when repairing the

unit.

10. Lubricate load chain per hoist manufacturer’s

recommendations.

11.

use the hoist’s overload limiting clutch to measure load.

12.

use limit switches as routine operating stops. They are

emergency devices only.

13.

allow your attention to be diverted from operating 

the hoist.

14.

allow the hoist to be subjected to sharp contact with

other hoists, structures, or objects through misuse.

15.

adjust or repair the hoist unless qualified to perform

such adjustments or repairs.