Справочник Пользователя для Tandberg Data 1080P
D14640.01—MARCH 2010
26
TANDBERG PrecisionHD 1080p/720p camera
Camera User Guide
Contents
Introduction
Physical interface
Cables
Connecti to codec
Video formats
Daisy chaining
Appendices
Contact us
www.tandberg.com
Debug commands for TANDBERG cameras
NOTE:
Never route these messages through Sony cameras. They are provided for debugging on the
TANDBERG PrecisionHD cameras only, and do not conform to the Visca length requirements.
Command set
Command packet
Comments
SW start
8x 01 50 a2 0p 0q 0r
0s 0t 0u 0v 0w ff
0s 0t 0u 0v 0w ff
pqrstuvw = size, pq=LSB Returns y050ff if ok.
Fatal errors: Returns y06006ff if upload already
in progress. Returns y06007ff if unable to
access the flash.
Fatal errors: Returns y06006ff if upload already
in progress. Returns y06007ff if unable to
access the flash.
SW end
8x 01 50 a1 ff
Sent after last SW packet, instructs camera to
verify new application. Command may take up
to 30 seconds to complete.
Returns y050ff if ok. Issue a camera reboot to
activate new software.
Returns y06008ff if verification of sw failed.
verify new application. Command may take up
to 30 seconds to complete.
Returns y050ff if ok. Issue a camera reboot to
activate new software.
Returns y06008ff if verification of sw failed.
SW abort
8x 01 50 a3 ff
Abort sw upload in progress
SW packet
8x a0 pp qq rr ss
[256 bytes data]
[256 bytes data]
ppqq = 16 bit packet id, pp=LSB
rrss = 16 bit CRC, rr=LSB
Returns y0 50 ff if packet ok.
-> send next one.
Returns y0 60 09 ff if crc error -> retransmit
packet.
Returns y0 60 0a ff if id error
-> retransmit packet
Fatal errors:
y0 60 0b ff not in upload mode
y0 60 0c ff error writing data to flash
NOTE: Entire message after 8x a0... is raw
data, so it may contain 0xff. Header is kept as
short as possible. Never route this message
through Sony cameras.
rrss = 16 bit CRC, rr=LSB
Returns y0 50 ff if packet ok.
-> send next one.
Returns y0 60 09 ff if crc error -> retransmit
packet.
Returns y0 60 0a ff if id error
-> retransmit packet
Fatal errors:
y0 60 0b ff not in upload mode
y0 60 0c ff error writing data to flash
NOTE: Entire message after 8x a0... is raw
data, so it may contain 0xff. Header is kept as
short as possible. Never route this message
through Sony cameras.
Command set
Command packet
Comments
CAM_PingPong_
Reset
Reset
8x ae ff
Reset ping ctr to 0.
CAM_Ping
8x af 0p 0q 0r 0s
[256 bytes data] ff
[256 bytes data] ff
pqrs = Pingval. Camera will respond with OK
if correct pingval received. Increase ctr with 1
for next packet. Data section will be dumped to
stdout if it fails.
if correct pingval received. Increase ctr with 1
for next packet. Data section will be dumped to
stdout if it fails.
CAM_Stdin
8x a4 [0-256 bytes
stdin] 00 ff
stdin] 00 ff
Send command to the command interpreter.
CAM_Debug_
Mode
Mode
8x 01 39 0q ff
q=0: Debug mode off.
q=1: Debug mode on. Camera will send stdout
as visca messages in the following format:
y0 50 [0-256 bytes stdout] 00 ff
q=1: Debug mode on. Camera will send stdout
as visca messages in the following format:
y0 50 [0-256 bytes stdout] 00 ff
Command set
Command packet
Comments
CAM_Boot
8x 01 42 ff
Reboot the camera. This will also reset serial
speed to 9600.
speed to 9600.
CAM_Speed
8x 01 34 0p ff
p=0: Serial speed 9600. p=1: Serial speed
115200. Reply will be sent before the speed
switch takes place. Please wait 20ms after ok
before sending new commands.
115200. Reply will be sent before the speed
switch takes place. Please wait 20ms after ok
before sending new commands.
The VISCA™/RS–232 control protocol, cont...
Software upload commands
The CRC algorithm used, is the same as in the XModem protocol. CRC for the last data packet is only
calculated for the actual data bytes in the packet. Pad last packet with 0x00 so that the data section
is 256 bytes long. The PacketID counter starts at 0.
calculated for the actual data bytes in the packet. Pad last packet with 0x00 so that the data section
is 256 bytes long. The PacketID counter starts at 0.
Other commands
Contact us
Contents
Introduction
Cables
Daisy chaining
Appendices
Physical interface
Connect to codec
Video formats
Appendices