Справочник Пользователя для Pelco PV1016RN
Hardware Setup
■
Remove the DIP switch cover from the rear of the Transmitter and set SW 1 and SW 2 according to the appropriate table.
PV1016T Transmitter with PV110 Modem
1
2
3
4
5
6
7
8
SW 1
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW 2
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PV1016TN Transmitter with PV120 Terminal Adapter*
1
2
3
4
5
6
7
8
SW 1
ON
ON
OFF
ON
ON
ON
OFF
OFF
SW 2
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PV1004T Transmitter with PV110 Modem
1
2
3
4
5
6
7
8
9
10
SW 1
ON
ON
ON
ON
N/A
N/A
N/A
N/A
N/A
N/A
SW 2
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
PV1004T Transmitter with PV120 Terminal Adapter*
1
2
3
4
5
6
7
8
9
10
SW 1
ON
ON
ON
ON
N/A
N/A
N/A
N/A
N/A
N/A
SW 2
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
ON
*Program the PV120 in accordance with the Instruction Sheet (C1918M) included in the PV120 package prior to connecting it to the
Transmitter. It must match the configuration of the PV120 used for the Receiver. DIP switch settings for the PV120 are correct out of the
box.
Transmitter. It must match the configuration of the PV120 used for the Receiver. DIP switch settings for the PV120 are correct out of the
box.
■
Set the DIP switches on the rear of the PV110 modem according to the table below.
PV110 Modem DIP Switch Settings
1
2
3
4
5
6
7
8
ON
ON
OFF
OFF
ON
ON
OFF
OFF
■
Connect the modem or terminal adapter to the Transmitter using the supplied cable.
■
Connect the Transmitter to an approved power source.
■
Connect a camera to camera input A1 on the rear of the Transmitter.
■
Connect phone line(s) and power supply to the modem or terminal adapter.
■
Switch power ON to the Modem/Terminal Adapter first, then turn on the Transmitter. The Modem/Terminal Adapter will take
a moment to “handshake” with the Transmitter. If Transmitter and Modem/Terminal Adapter will not successfully handshake,
confirm programming and/or DIP switch settings. When the handshake is complete the Transmitter is ready to transmit video.
a moment to “handshake” with the Transmitter. If Transmitter and Modem/Terminal Adapter will not successfully handshake,
confirm programming and/or DIP switch settings. When the handshake is complete the Transmitter is ready to transmit video.
BACK-TO-BACK RECEIVER AND TRANSMITTER SETUP
This section will detail the minimum steps necessary to establish a back-to-back, demonstration mode, connection between a
PelcoVision™ Receiver and a PelcoVision™ Transmitter. This setup does not require modems or terminal adapters.
PelcoVision™ Receiver and a PelcoVision™ Transmitter. This setup does not require modems or terminal adapters.
1
2
HI
LO
B
LOOP
HI
LO
B
LOOP
HI
LO
B
LOOP
HI
LO
B
LOOP
3
4
5
6
HI
LO
B
LOOP
HI
LO
B
LOOP
HI
LO
B
LOOP
HI
LO
B
LOOP
7
8
B
A
SW1
SW2
MODEM
ALARM
COM 2
COM 1
MONITOR
KEYBOARD
REAR
CAMERA INPUT A1
SW 1
SW 2
MODEM PORT
AC POWER
PV1016T
Figure 3. PV1016T Rear Panel
SETTING UP A TRANSMITTER TO RECEIVE A CALL
This section details the minimum steps necessary to set up a Transmitter for transmission of video to a Receiver. Refer to Figure 3
when setting DIP switches and making cable connections to the PV1016T.
when setting DIP switches and making cable connections to the PV1016T.