Справочник Пользователя для Pelco C2953M-B
C2953M-B (10/09)
9
PRODUCT LABEL
The product label lists the model number, date code, serial number, and Media Access Control (MAC) address. This information might be required
for setup. To access the product label remove the back cover of the camera (refer to Figure 2 and Figure 3).
for setup. To access the product label remove the back cover of the camera (refer to Figure 2 and Figure 3).
Figure 2. Remove Back Cover
Figure 3. Product Label
ì
RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera through the network using PoE. If PoE
is not available, the camera is prewired for 24 VAC.
is not available, the camera is prewired for 24 VAC.
î
Ethernet Activity LED: Flashes green to indicate that data is being transmitted or received by the camera.
ï
Ethernet Link LED: Glows solid amber to indicate that a live network connection is established.
ñ
Accessory Port: For use with compatible Pelco accessories.
ó
24 VAC Power, Relay, and Alarm Connections: Supports 24 VAC as the power source, one relay that can be used to control an
external circuit, and one alarm for physical input into the system.
external circuit, and one alarm for physical input into the system.
r
Reset Button: Reboots the camera or restores the camera’s factory default settings. This button is recessed. Using a small tool, such
as a paper clip, press and release the reset button once to reboot the camera. Press and hold the reset button for 10 seconds to restore
the camera to the factory default settings.
as a paper clip, press and release the reset button once to reboot the camera. Press and hold the reset button for 10 seconds to restore
the camera to the factory default settings.
s
Mini SD Card Slot: Saves a snapshot image to a mini SD card based on alarm activity.
NOTE: The mini SD card must be formatted as FAT32. Other formats are not compatible with the camera.
NOTE: The mini SD card must be formatted as FAT32. Other formats are not compatible with the camera.
t
Service Port: Outputs analog video. Use this port at the installation site to set up the field of view and to focus the camera. When a
service cable is connected to the camera, video to the IP stream is disabled (refer to Service Cable on page 12).
service cable is connected to the camera, video to the IP stream is disabled (refer to Service Cable on page 12).
u
Power LED: Glows solid amber and then flashes green during the configuration sequence; glows solid green after the sequence is
complete. The LED can be disabled. If this LED glows red (solid or flashing), contact Pelco Product Support at 1-800-289-9100 (USA and
Canada) or +1-559-292-1981 (international) for assistance.
complete. The LED can be disabled. If this LED glows red (solid or flashing), contact Pelco Product Support at 1-800-289-9100 (USA and
Canada) or +1-559-292-1981 (international) for assistance.
~í
Auto Iris Lens Connector: Controls the amount of light allowed through the lens. Insert the 4-pin connector from the DC drive auto iris
lens into this connector
lens into this connector
~â
Auto Back Focus Button: Sets the auto back focus mechanism. Press the button once to center the auto back focus mechanism and
to fully open the iris. Press and hold the button for three seconds to start the auto back focus mechanism and to focus the camera.
to fully open the iris. Press and hold the button for three seconds to start the auto back focus mechanism and to focus the camera.
~ä
NTSC/PAL Button: Toggles the service connector between NTSC and PAL formats. The default setting is NTSC.
DC01234 SN:123-4567
00:15:C5:3A:84:DB
00:15:C5:3A:84:DB
IXE20C
A1.0
US
LISTED
C
N15007
AMPS
390mA
390mA
MAX
VOLTS
24V~
ITE
15KT