Справочник Пользователя для Ryobi RY34001

4 — English



  Inspect before use. Replace damaged parts. Make sure 

fasteners are in place and secure. Check for fuel leaks.



  Replace string head if cracked, chipped, or damaged 

in any way. Be sure the string head or blade is properly 
installed and securely fastened. Failure to do so can cause 
serious injury.



  Make sure all guards, straps, deflectors, and handles are 

properly and securely attached.



 Use only the manufacturer’s replacement line in the 

cutting head. Do not use any other cutting attachment. 
To install any other brand of replacement line or cutting 
head to this string trimmer can result in serious personal 
injury. Never use, for example, wire or wire-rope, which 
can break off and become a dangerous projectile.



  Never operate unit without the grass deflector in place 

and in good condition.



  Never use blades, flailing devices, wire, or rope on trimmer 

attachment.



  Maintain a firm grip on both handles while trimming. Keep 

string head below waist level. Never cut with the string 
head located over 30 in. or more above the ground.



  Brushcutter blades coast after throttle trigger is released 

or engine is stopped. Keep the rotating blade in thicker 
weeds or pulpy stalks until the blade completely stops.



  Do not operate the brushcutter unless the brushcutter 

guard is firmly secured in place and in good condition.



  Use heavy gloves when operating the brushcutter and 

when installing or removing blades.



  Always stop the engine and remove the spark plug wire 

before attempting to remove any obstruction caught or 
jammed in the blade or before removing and installing 
the blade.



  Do not attempt to touch or stop the blade when it is 

rotating.



 A coasting blade can cause injury while it continues  

to spin after the engine is stopped or throttle trigger 
released. Maintain proper control until the blade has 
completely stopped rotating.



  Replace any blade that has been damaged. Always make 

sure blade is installed correctly and securely fastened 
before each use. Failure to do so can cause serious 
injury.



  Use only the manufacturer’s replacement Tri-Arc

®

 blade 

intended for use on this brushcutter. Do not use any other 
blade. To install any other brand blade or cutting head to 
this brushcutter can result in serious personal injury.



  The Tri-Arc

®

 blade is suited for cutting thicker weeds or 

pulpy stalks only. Do not use for any other purpose. Never 
use the Tri-Arc

®

 blade to cut woody brush.



  Exercise extreme caution when using the blade with this 

unit. Blade thrust is the reaction that may occur when 
the spinning blade contacts anything it cannot cut. This 
contact may cause the blade to stop for an instant, and 
suddenly “thrust” the unit away from the object that was 
hit. This reaction can be violent enough to cause the 
operator to lose control of the unit. Blade thrust can occur 
without warning if the blade snags, stalls, or binds. This is 
more likely to occur in areas where it is difficult to see the 
material being cut. For cutting ease and safety, approach 
the weeds being cut from the right to the left. In the event 
an unexpected object or woody stock is encountered, 
this could minimize the blade thrust reaction.



  Never cut any material over 1/2 in. diameter.



 Always wear the shoulder harness  when using the 

brushcutter and adjust to a comfortable operating position. 
Maintain a firm grip on both handles while cutting with a 
blade. Keep the blade away from your body and below 
waist level.



  Never use the brushcutter with the blade located 30 in. 

or more above the ground level.



  Save these instructions.

 Refer to them frequently and use 

them to instruct others who may use this tool. If you loan 
someone this tool, loan them these instructions also.



  Allow the engine to cool; empty the fuel tank and secure 

the unit from moving before transporting in a vehicle.



  Wear your protective equipment and observe all safety 

instructions. For units equipped with a clutch, be sure 

the cutting attachment stops turning when the engine 
idles. When the unit is turned off make sure the cutting 
attachment has stopped before the unit is set down.