Листовка для Mitsubishi Electronics GT15-75ABUS2L

User's Manual

Thank you for purchasing the GOT1000 Series.

GT15-75BUSL-U

1D7M04

IB(NA)-0800298-J(1106)MEE

z

SAFETY PRECAUTIONSz

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant
manuals introduced in this manual carefully and pay full attention to
safety to handle the product correctly.
The precautions given in this manual are concerned with this prod-
uct.
In this manual, the safety precautions are ranked as "DANGER" and
"CAUTION".

Note that the 

CAUTION level may lead to a serious accident

according to the circumstances. 
Always follow the precautions of both levels because they are impor-
tant to personal safety.
Please save this manual to make it accessible when required and
always forward it to the end user.

Indicates that incorrect handling may cause 
hazardous conditions, resulting in death or 
severe injury.

Indicates that incorrect handling may cause 
hazardous conditions, resulting in medium or 
slight personal injury or physical damage.

z

Do not bunch the control wires or communication cables with 
the main circuit or power wires, or lay them close to each other.
As a guide, separate the lines by a distance of at least 100mm 
(3.94 inches) otherwise malfunctions may occur due to noise.

z

Before mounting or dismounting this unit to or from the GOT, 
always shut off GOT power externally in all phases.
Not doing so can cause a unit failure or malfunction.

z

Use this unit in the environment that satisfies the general 
specifications described in the User's Manual for the GOT used. 
Not doing so can cause an electric shock, fire, malfunction or 
product damage or deterioration.

z

When installing this unit to the GOT, fit it to the connection 
interface of the GOT and tighten the mounting screws in the 
specified torque range.
Undertightening can cause a drop, failure or malfunction. 
Overtightening can cause a drop, failure or malfunction due to 
screw or unit damage.

z

Before connecting the Bus connection cable to this unit, always 
shut off GOT power and PLC CPU power externally in all 
phases.
Not doing so can cause a malfunction.

z

Insert and fit the bus connection cable into the connector of the 
unit to be connected until it "clicks".
After fitting, check for lift which can cause a malfunction due to a 
connection fault.

z

Before starting cleaning, always shut off GOT power externally 
in all phases. Not doing so can cause a unit failure or 
malfunction.

z

Do not disassemble or modify any unit. 
This will cause failure, malfunction, injuries, or fire.

z

Do not touch the conductive areas and electronic parts of this 
unit directly.
Doing so can cause a unit malfunction or failure.

z

Always secure the cables connected to the unit, e.g. run them in 
conduits or clamp them.Not doing so can cause unit or cable 
damage due to dangling, moved or accidentally pulled cables or 
can cause a malfunction due to a cable contact fault.

z

Do not hold the cable part when unplugging any cable 
connected to the unit. Doing so can cause unit or cable damage 
or a malfunction due to a cable contact fault.

z

Always make sure to touch the grounded metal to discharge the 
electricity charged in the body, etc., before touching the unit. 
Failure to do so may cause a failure or malfunctions of the unit.

z

Dispose of this product as industrial waste.

The following shows manuals relevant to this product.

For relevant manuals, refer to the PDF manuals stored in the CD-
ROM for the drawing software used.

© 2004 MITSUBISHI ELECTRIC CORPORATION

To configure a system meeting the requirements of the EMC and Low 
Voltage Directives when incorporating the Mitsubishi GOT (EMC and 
Low Voltage Directives compliant) into other machinery or 
equipment, refer to "EMC AND LOW VOLTAGE DIRECTIVES" of the 
General Description included with the GOT used.
The CE mark, indicating compliance with the EMC and Low Voltage 
Directives, is printed on the rating plate of the GOT.

This product complies with the Radio Waves Act (South Korea).
Note the following when using the product in South Korea.

이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자
는 이 점을 주의하시기 바라며, 가정외의 지역에서 사용하는 것을 
목적으 로 합니다 .

(The product is for business use (Class A) and meets the 
electromagnetic compatibility requirements. 
The seller and the user must note the above point, and use the 
product in a place except for home.)

The following items are included.

z

Make sure to transport the GOT main unit and/or relevant unit(s) 
in the manner they will not be exposed to the impact exceeding 
the impact resistance described in the general specifications of 
the User's Manual for the GOT used, as they are precision 
devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.

Detailed Manual

Manual name

Manual number

(Model code)

GT16 User's Manual (Hardware)

(Sold separately)

SH-080928ENG

(1D7MD3)

GT15 User's Manual

(Sold separately)

SH-080528ENG

(1D7M23)

GOT1000 Series Connection Manual
(Mitsubishi Products) for GT Works3

(Sold separately)

SH-080868ENG

(1D7MC2)

Relevant Manuals

Model

Product

Quantity

GT15-75QBUSL,
GT15-75QBUS2L,
GT15-75ABUSL,
GT15-75ABUS2L

Bus connection unit

1

Stickers

12

This User's Manual describes the GT15 bus connection unit 
(hereinafter referred to as the bus connection unit).
Use the bus connection unit for making bus connection of the GOT.
Refer to the User's Manual for the GOT used for the applicable GOT.

The performance specifications of the bus connection unit are 
indicated below.
The general specifications of the bus connection unit are the same 
as those of the GOT.
Refer to the User's Manual for the GOT used for the general 
specifications of the GOT.

* When the GOT power is on, the internal current consumption is

included in the current consumption of the GOT.
When the GOT power is off, the internal current is supplied from
the power supply of the PLC system.

Select the used bus connection unit according to the connection 
target and connection position.

(1) Select the bus connection unit according to the connection target.

When using the bus connection, make the communication 
settings to perform communication between the GOT and PLC.
Refer to GOT1000 Series Connection Manual for details of bus 
connection.

Item

GT15-

75QBUSL

GT15-

75QBUS2L

GT15-

75ABUSL

GT15-

75ABUS2L

Interface

QCPU (Q Mode)

bus connection

QnA/ACPU

bus connection

Connector

IN

1

1

1

1

OUT

-

1

-

1

I/O occupied 

points

16 points 

(I/O assignment:16 

intelligent points)

32 points 

(I/O assignment:

Special  32 points)

Internal current 

consumption

 (5VDC)*

0.44A

0.44A

0.12A

0.12A

Weight

0.13kg

(0.29lb)

0.14kg

(0.31lb)

0.13kg

(0.29lb)

0.14kg

(0.31lb)

(2)  Select the bus connection unit according

to the GOT connection position.

  Placed midway
 : GT15-75QBUS2L/GT15-75ABUS2L

  Placed at end
 : GT15-75QBUSL/GT15-75ABUSL
   GT15-75QBUS2L/GT15-75ABUS2L

  QCPU (Q Mode), motion controller Q series
 

   : GT15-75

Q

BUSL/GT15-75

Q

BUS2L

  ACPU, QnACPU, motion controller A series
 

   : GT15-75

A

BUSL/GT15-75

A

BUS2L

Unit: mm (inch)

Dimensions of X when the bus connection unit is mounted to the 
GOT

Unit : mm(inch)

*1 When the GT15-75QBUSL/GT15-75ABUSL is used, only the IN 

side connector is available.

Model

A

GT15- 75QBUSL

2.5(0.10)

GT15- 75QBUS2L

2.5(0.10)

GT15- 75ABUSL

4(0.16)

GT15- 75ABUS2L

4(0.16)

GOT

GT16

GT15

15”

6.5 (0.26)

8 (0.31)

12.1”

5(0.20)

5 (0.20)

10.4”

8(0.31)

8(0.31)

8.4”

10 (0.39)

10 (0.39)

5.7”

10 (0.39)

10 (0.39)

137(5.39)

102(4.02)

4)

4)

5)

*1

2)

1)

17.5 (0.69)

Back view

3)

X

GOT

A

The installation procedure for the bus connection unit is explained 
using the GT1575.

(1) Power off the GOT.

(2) Remove two extension unit covers of the GOT.

(3) Fit the bus connection unit in the GOT case.

No.

Name

Description

1)

Bus connector (IN side)

Connector for connecting the 
bus connection cable (IN side)

2)

Bus connector (OUT 
side)

Connector for connecting the 
bus connection cable (OUT side)

3)

Extended connector

Extension connector mounted to 
the GOT

4)

Mounting screw

Screw (M3 screw) for fixing the 
unit to the GOT

5)

Rating plate

-

(4) Fasten the bus connection unit by tightening its mounting screws 

(4 places) with tightening torgue 0.36 to 0.48 N•m.

(5) After tightening screws, attach the supplied stickers to avoid 

receiving electrostatic.

Mitsubishi will not be held liable for damage caused by factors found 
not to be the cause of Mitsubishi; machine damage or lost profits 
caused by faults in the Mitsubishi products; damage, secondary 
damage, accident compensation caused by special factors 
unpredictable by Mitsubishi; damages to products other than 
Mitsubishi products; and to other duties.

• This product has been manufactured as a general-purpose part for 

general industries, and has not been designed or manufactured to 
be incorporated in a device or system used in purposes related to 
human life. 

• Before using the product for special purposes such as nuclear 

power, electric power, aerospace, medicine or passenger 
movement vehicles, consult with Mitsubishi.

• This product has been manufactured under strict quality control. 

However, when installing the product where major accidents or 
losses could occur if the product fails, install appropriate backup or 
failsafe functions in the system.

Country/Region Sales office/Tel
U.S.A 

Mitsubishi Electric Automation Inc.

 

500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A.

 

Tel : +1-847-478-2100

Brazil  

MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.

 

Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar 

 

Paraiso, Sao Paulo, SP Brazil

 

Tel : +55-11-5908-8331

Germany  

Mitsubishi Electric Europe B.V. German Branch

 

Gothaer Strasse 8 D-40880 Ratingen, GERMANY

 

Tel : +49-2102-486-0

U.K  

Mitsubishi Electric Europe B.V. UK Branch

 

Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K.

 

Tel : +44-1707-276100

Italy  

Mitsubishi Electric Europe B.V. Italian Branch

 

Centro Dir. Colleoni, Pal. Perseo-Ingr.2

 

Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy

 

Tel : +39-039-60531

Spain  

Mitsubishi Electric Europe B.V. Spanish Branch

 

Carretera de Rubi 76-80,

 

E-08190 Sant Cugat del Valles, Barcelona, Spain

 

Tel : +34-93-565-3131

France  

Mitsubishi Electric Europe B.V. French Branch

 

25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France

 

Tel : +33-1-5568-5568

South Africa 

Circuit Breaker Industries Ltd.

 

Private Bag 2016, ZA-1600 Isando, South Africa

 

Tel : +27-11-928-2000

Hong Kong 

Mitsubishi Electric Automation (Hong Kong) Ltd.

 

10th Floor, Manulife Tower, 169 Electric

 

Road, North Point, Hong Kong

 

Tel : +852-2887-8870

China  

Mitsubishi Electric Automation (China) Ltd.

 

4/F Zhi Fu Plazz, No.80 Xin Chang Road,

 

Shanghai 200003, China

 

Tel : +86-21-6120-0808

Taiwan  

Setsuyo Enterprise Co., Ltd.

 

6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang, 

 Taipei 

Hsine, 

Taiwan

 

Tel : +886-2-2299-2499

Korea  

Mitsubishi Electric Automation Korea Co., Ltd.

 

1480-6, Gayang-dong, Gangseo-ku Seoul

 157-200, 

Korea

 

Tel : +82-2-3660-9552

Singapore  

Mitsubishi Electric Asia Pte, Ltd.

 307 

Alexandra 

Road 

#05-01/02,

 

Mitsubishi Electric Building, Singapore 159943

 

Tel : +65-6470-2460

Thailand  

Mitsubishi Electric Automation (Thailand) Co., Ltd.

 

Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd, 

 T.Kannayao, 

A.Kannayao, 

Bangkok 

10230 

Thailand

 

Tel : +66-2-517-1326

Indonesia  

P.T. Autoteknindo Sumber Makmur

 

Muara Karang Selatan, Block A/Utara 

 

No.1 Kav. No.11 Kawasan Industri Pergudangan 

 

Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia

 

Tel : +62-21-6630833

India  

Messung Systems Pvt, Ltd.

 

Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari, 

 Pune-411026, 

India

 

Tel : +91-20-2712-3130

Australia  

Mitsubishi Electric Australia Pty. Ltd.

 

348 Victoria Road, Rydalmere, N.S.W 2116, Australia

 

Tel : +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry 
of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.
Printed in Japan, June 2011.