Справочник Пользователя для Ariens 920401
GB - 12
CONTROLS
AND FEATURES
See Figure 7 for all Controls and Features
locations.
locations.
Dual Handle Interlock
When attachment clutch and then traction
drive clutch are engaged, the attachment
clutch will remain engaged (lever down) if
released. To stop attachment, release traction
drive clutch and both clutches will disengage.
drive clutch are engaged, the attachment
clutch will remain engaged (lever down) if
released. To stop attachment, release traction
drive clutch and both clutches will disengage.
Traction Drive Clutch - Left Hand
Lever
Lever
Squeeze the traction drive
clutch lever against the
handlebar (1) to engage
wheel drive for propelling
unit. Forward speed will
vary according to snow
depth and moisture
content.
clutch lever against the
handlebar (1) to engage
wheel drive for propelling
unit. Forward speed will
vary according to snow
depth and moisture
content.
Release lever (2) to stop
movement.
movement.
NOTE: When traveling to or from the area to
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
Attachment Clutch - Right Hand
Lever
Lever
Squeeze attachment
clutch lever against
handlebar (1) to
engage attachment.
Release both clutch
levers (2) to disengage
power and apply brake
to attachment.
clutch lever against
handlebar (1) to
engage attachment.
Release both clutch
levers (2) to disengage
power and apply brake
to attachment.
IMPORTANT: If the belt squeals when the
attachment clutch lever is engaged, the
impeller may be frozen in the auger housing.
Immediately release the attachment clutch
lever and move the unit into a heated area to
thaw.
NOTE: If belt squeals when impeller turns
freely, see Attachment Drive Belt
Replacement on page 20.
attachment clutch lever is engaged, the
impeller may be frozen in the auger housing.
Immediately release the attachment clutch
lever and move the unit into a heated area to
thaw.
NOTE: If belt squeals when impeller turns
freely, see Attachment Drive Belt
Replacement on page 20.
Ignition Switch (Push/Pull Safety
Key)
Key)
Key Switch has two positions:
1. “Stop” - pulled out
2. "Run" - pushed in
2. "Run" - pushed in
NOTE: DO NOT twist key after it is inserted.
Engine Shutoff Switch
1. Set the engine shutoff switch to the run
position ("Run") to start and operate the
engine.
engine.
2. Set the engine shutoff switch to the stop
position ("Stop") to shut off a running
engine.
engine.
Primer Bulb
Pushing the primer bulb in adds fuel for
easier engine start. Refer to Starting and Shut
Off on page 15.
easier engine start. Refer to Starting and Shut
Off on page 15.
Speed Selector
Position the speed selector in the appropriate
speed notch to control forward and reverse
travel.
speed notch to control forward and reverse
travel.
OPERATION
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
and understand the entire Safety
section before proceeding.
WARNING: To avoid injury to hands
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Keep hands and feet away from
auger and impeller.
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Keep hands and feet away from
auger and impeller.
1
2
OL2701
1
2
OL2691
2
1
OS8225
1
2
6
1
08000127A