Справочник Пользователя для Ariens 920401
GB - 27
13. Insert new friction disc assembly into
frame. Install washers onto carrier
bearing and slide into speed selector
arm.
bearing and slide into speed selector
arm.
14. Slide hex shaft through new friction disc
assembly. Install pinion gear and washer
onto hex shaft and slide shaft into right
bearing.
onto hex shaft and slide shaft into right
bearing.
15. Install left bearing flange using hardware
removed in step 7.
16. Reinstall clip pin into hex shaft.
17. Connect pivot pin to speed selector arm.
17. Connect pivot pin to speed selector arm.
18. Install bottom cover.
19. Reinstall wheels.
20. Return unit to upright position.
21. Connect spark plug wire to spark plug.
22. Adjust traction drive clutch. See
19. Reinstall wheels.
20. Return unit to upright position.
21. Connect spark plug wire to spark plug.
22. Adjust traction drive clutch. See
SHORT TERM
IMPORTANT: NEVER spray unit with high
pressure water or store unit outdoors.
pressure water or store unit outdoors.
Run with attachment clutch engaged a few
minutes after each use to free unit of any
loose or melting snow.
minutes after each use to free unit of any
loose or melting snow.
Close fuel shut-off valve.
Inspect unit for visible signs of wear,
breakage or damage.
Inspect unit for visible signs of wear,
breakage or damage.
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
tightened and know unit is in safe working
condition.
Store unit in a cool, dry protected area.
LONG TERM
Clean unit thoroughly with mild soap and low
pressure water and lubricate (see
MAINTENANCE on page 16). Touch up all
scratched painted surfaces.
pressure water and lubricate (see
MAINTENANCE on page 16). Touch up all
scratched painted surfaces.
Remove weight from wheels by putting
blocks under frame or axle.
blocks under frame or axle.
Fuel System
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
To treat the fuel system for storage:
1. Add fuel stabilizer according to
manufacturers’s instructions.
2. Run engine for at least 10 minutes after
adding stabilizer to allow it to reach the
carburetor.
carburetor.
NEVER store the engine with fuel in the fuel
tank inside of a building with potential
sources of ignition.
tank inside of a building with potential
sources of ignition.
STORAGE
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
and understand the entire Safety
section before proceeding.
SERVICE PARTS
Order the following parts through your
dealer:
dealer:
Part No.
Description
00036800 Ariens Hi-Temp Grease (3, 3 oz.
cartridges)
21547400 Spark Plug
07200513 Impeller Belt
07200101 Traction Belt
53200500 Shear Bolts
00170800 Friction Disc
00592900 Gas Stabilizer (4 oz.)
ACCESSORIES
See your authorized Ariens dealer to add the
additional accessories available to your
Sno-Tek model.
additional accessories available to your
Sno-Tek model.
Part No.
Description
72000200 Slicer Bar
72406500 Front Weight Kit
72600300 Composite Skid Shoe Kit
73203600 Snow Thrower Cover