Справочник Пользователя для Roland 04672434
154
Chapter 8 Parameter Guide SYSTEM
FC-300 CTL6
FC-300 external footswitch6
FC-300 E5/C7
FC-300 external expression pedal5/external
footswitch7
footswitch7
FC-300 CTL8
FC-300 external footswitch8
INTRNL PEDAL
Internal pedal
WAVE PEDAL
Wave pedal
TARGET
Used in the general V-LINK compatible device.
DISLV CC #5
Dissolve time
(time elapsed in switching video images)
(time elapsed in switching video images)
Cb CC #74
Color cb (Color difference signal)
Cr CC #71
Color cr (Color difference signal)
Used in the motion dive .tokyo performance package.
COLOR EQ-FG
Color foreground
COLOR EQ-BG
Color background
SCRTCH SW
Scratch switch
SPEED KNOB
Speed knob
TOTAL FADER
Total fader
CROSS FADER
Cross fader
BPM SYNC
BPM sync switch
CLIP LOOP
Clip loop switch
ASSIGN KNOB
Assignable knob
FADE TIME
Fade time switch
VISUAL KNOB
Visual plug-in control knob
AB SW
A/B switch
TAP SW
Tap switch
TOTAL SELECT
Total select
FX SELECT
Effect select
PLAY POS
Play position
LOOP START
Loop start position
LOOP END
Loop end position
LAYER MODE
Layer mode select
DV-7PR
PLAY SPEED
Play speed
DISLV TIME
Dissolve time
(time elapsed in switching video images)
(time elapsed in switching video images)
T BAR
T bar
COLOR Cb
Color cb (Color difference signal)
COLOR Cr
Color cr (Color difference signal)
BRIGHTNESS
Brightness
VFX 1
Visual effects1
VFX 2
Visual effects2
VFX 3
Visual effects3
VFX 4
Visual effects4
OUTPUT FADE
Output fade
DUAL STREAM
Dual stream
MIN (Minimum) *1
0–127
Sets the lower limit in the range the param-
eter changes.
eter changes.
MAX (Maximum) *1
0–127
Sets the upper limit in the range the param-
eter changes.
eter changes.
Parameter/
Range
Range
Explanation
Parameter/
Range
Range
Explanation
TRIGGR (Trigger) *2
Sets the point at which the virtual expression pedal’s action begins.
PATCH CHANGE
Functions when patches are switched.
GK VOL
Functions when the divided pickup’s vol-
ume knob is adjusted.
ume knob is adjusted.
GK S1, S2
Functions when the divided pickup’s
DOWN/S1 or UP/S2 switch position is
changed.
DOWN/S1 or UP/S2 switch position is
changed.
CTL1–CTL4
Functions when the CTL 1, 2 buttons or foot
switch connected to CTL 3,4 jack are operat-
ed.
switch connected to CTL 3,4 jack are operat-
ed.
EXP PEDAL
Functions when the expression pedal con-
nected to EXP PEDAL jack are operated.
nected to EXP PEDAL jack are operated.
D BEAM V, H
Functions when the vertical or horizontal
position is detected by the D Beam control-
ler.
position is detected by the D Beam control-
ler.
RIBBON ACT, POS
Functions when the ribbon controller is op-
erated by touch or when the position is de-
tected.
erated by touch or when the position is de-
tected.
FC-300 EXP1, EXP2
Functions when the FC-300’s EXP PEDAL 1
or 2 is operated.
or 2 is operated.
FC-300 CTL1, CTL2
Functions when the FC-300’s CTL1 or CTL2
is operated.
is operated.
FC-300 E3/C3, CTL4,
E4/C5, CTL6, E5/C7,
CTL8
E4/C5, CTL6, E5/C7,
CTL8
Functions when a pedal connected to the
FC-300’s E3/C3, CTL4, E4/C5, CTL6, E5/
C7, or CTL8 jacks is operated.
FC-300’s E3/C3, CTL4, E4/C5, CTL6, E5/
C7, or CTL8 jacks is operated.
TIME *2
0–100
Adjusts the amount of time for the virtual
expression pedal to shift from the fully re-
leased position (pedal toe raised) to the fully
depressed position (pedal toe pressed
down).
expression pedal to shift from the fully re-
leased position (pedal toe raised) to the fully
depressed position (pedal toe pressed
down).
CURVE *2
This selects one of the three types that determines how the assumed
expression pedal changes.
expression pedal changes.
RATE *3
0–100
This determines the time spend for one cycle
of the assumed expression pedal.
of the assumed expression pedal.
FORM *3
This selects one of the three types that determines how the assumed
expression pedal should change.
expression pedal should change.
LINEAR
SLOW RISE
FAST RISE
SAW
TRI
SIN
VB-99_e.book 154 ページ ２００８年８月１８日 月曜日 午後１時１０分