Справочник Пользователя для Studer Innotec C1312 COMPACT
STUDER INNOTEC
COMPACT
COMPACT
COMPACT
COMPACT
User manual
COMPACT V2.0 E
20
5.3.2 Set the voltage and timing
threshold
The programming is done in accordance
with the following steps:
Push and hold down, the Push Button 21
(Program) and the Push Button 19
(Change status) for minimum 2 seconds
simultaneously.
With the Push Button 20 (select) select
with of the battery level and the absorption
time to be changed.
These four red LED show the function
set:
Low voltage
with the following steps:
Push and hold down, the Push Button 21
(Program) and the Push Button 19
(Change status) for minimum 2 seconds
simultaneously.
With the Push Button 20 (select) select
with of the battery level and the absorption
time to be changed.
These four red LED show the function
set:
Low voltage
LED 13
Float charge
LED 12
Absorption (End of charge)
LED11
Equalization LED
10
Absorptions Time
LED 10/11/12/13
With the Push Button 19 (Change status) set the desired parameter (voltage or the time) to modify
(LED 14/15/16/17/18). Push Button 19 (Change status) to set the desired value according to the
the table 5.3.1.
If desired, repeat the operation with any other parameter (voltage or time) to be changed.
If during 10 seconds no buttons are pressed, the selected values are automatically stored and the
COMPACT switches back in to the normal operating status.
The voltage levels and times changed through programming are only first active with the
next charge cycle!
The voltage level which are not suitable can greatly reduce the battery life or could even
destroy it ! Therefore check beforehand with your battery supplier.
5.4 Program the auxiliary contact
5.4.1 Principle
The Auxiliary Contact can be basically programmed for any operating situation of the COMPACT
which is indicated with a LED. The programming is possible for one or more operating situations. If
the contact is programmed for many situations, it is activated as soon as the COMPACT finds itself
in any one of the programmed situations. That means that workings of the contact meets that of
the logic OR–Function.
5.4.2 The programming of the Auxiliary Contact is carried out in the following Steps:
The Push Button 21 (Program) press down for min. 2 seconds. The LED 4 „Program“ is lit as an
indication, that the COMPACT is in program mode.
A lit LED shows the programmed condition for the auxiliary contact. (LED 10/11/12/13 factory
setting)
With the Push Button 20 (select), select the desired condition in which the contact should be
activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If desired ,with the Push Button 20 (select) select another condition in which the contact should be
activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If during 10 seconds no buttons are pushed, then the settled values are automatically stored and
the COMPACT switches back to normal operating condition.
The Auxiliary Contact can be basically programmed for any operating situation of the COMPACT
which is indicated with a LED. The programming is possible for one or more operating situations. If
the contact is programmed for many situations, it is activated as soon as the COMPACT finds itself
in any one of the programmed situations. That means that workings of the contact meets that of
the logic OR–Function.
5.4.2 The programming of the Auxiliary Contact is carried out in the following Steps:
The Push Button 21 (Program) press down for min. 2 seconds. The LED 4 „Program“ is lit as an
indication, that the COMPACT is in program mode.
A lit LED shows the programmed condition for the auxiliary contact. (LED 10/11/12/13 factory
setting)
With the Push Button 20 (select), select the desired condition in which the contact should be
activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If desired ,with the Push Button 20 (select) select another condition in which the contact should be
activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If during 10 seconds no buttons are pushed, then the settled values are automatically stored and
the COMPACT switches back to normal operating condition.
OFF
Over Temp
Overload
ON/OFF
Batt Low/High
(Change status)
lock
RESET ALARM
3
4
5
6
20
10
11
12
14
21
13
19
15
16
17
18