Справочник Пользователя для Ingersoll-Rand 16574014
16574014_ed1
3
CA Angle Air Grinder, Die Grinder and Sander Parts List
Item
Part Description
Part Number Item
Part Description
Part
Number
Common parts for ALL CA Grinders
22 Angle Housing Assembly
LA1-A550S
1
Inlet Assembly
LG1-A465A
23
Clamp Spacer
LA1-46
2
Inlet Screen
R1602-61
24
Clamp Nut
LG1-27
• 3
Inlet Seal
85H-167
25
Grease Fitting
D0F9-879
Throttle Valve Cartridge Kit
LG1-K300
26
Upper Arbor Bearing
AG210-693
4
Throttle Valve Cartridge Case
LG1-300A
¤ 27
Wick
4A
Throttle Valve Seat
LG1-303
for CA120
LA1-560
4B
Throttle Valve
AG210-302
for CA200
LA1-561
4C
Throttle Valve Spring
7L-51
28 Bevel Gear Nut
AG210-578A
4D
Throttle Valve Spring Seat
LG1-592
29 Lower Arbor Bearing
AG210-24
5
Motor Housing
LG1-40
30 Arbor Bearing Cap
AG210-531
6
Throttle Lever
LG1-273
31 Arbor
6A
Locking Throttle Lever Assembly
(for models ending in L, C, ML or MC)
(for models ending in L, C, ML or MC)
LG1-A400
for all models ending in
G4, G4C or G4L
G4, G4C or G4L
AG210-4-G4
*
Lever Lock
LG1-402
for all models ending in
S4, S4C or S4L
S4, S4C or S4L
AG210-4-W2
*
Lock Spring
LG1-405
*
Lock Pin
5UT-757
for all models ending in
P63, P63C or P63L
P63, P63C or P63L
LA1-6
7
Throttle Lever Pin
61H-120
8
Throttle Valve Plunger
LG1-191
H63, H63C or H63L
LA1-103-1
9
Rear Rotor Bearing
DG230-22
*
Warning Label
• 10
Rear Rotor Bearing Spacer (2)
DG20-278
for models ending in P63-EU
EU-63--99
• 11
Rear Rotor Bearing Retainer
LG1-118
for all other models ending in-EU
EU-99
12
Rotor
for all other models
LG1-99
for CA120 (5 vane slots)
LG1-53-5
*
Nameplate
for CA200 (3 vane slots)
LG1-53-3
for CA120 models ending in-EU
LA112-EU-301
• 13
Vane Packet (set of 5 Vanes)
LG1-42-5
for all other CA120 models
LA112-301
14
Front End Plate
LG1-11
for CA200 models ending in-EU
LA120-EU-301
15
Front End Plate Spacer
DG10-65-5
for all other CA200 models
LA120-301
• 16
Front Seal Cup
LG1-32
Additional parts for all collet
models
models
17
Front Rotor Bearing
LG1-24
18
Flow Ring
32 Collet
for CA120 (12000 rpm) (brown)
LG1-103-1
for models ending in-EU
DG110-700-
for CA200 (20000 rpm) (red)
LG1-103-3
6mm
19
High Profile Flange
LG1-23
for all other models
DG110-700-
# 19A Low Profile Concentric Flange
(for all models ending in C)
LG1R-23
G4
33 Nosepiece
AG210-698A
20
Flange Clamp
LG1-29
34 Collet Nut
AG210-699A
21
Bevel Pinion and Bevel Gear
(sold only as a matched set)
(sold only as a matched set)
for CA120
LA1-A552-2.0S
for CA200
LA1-A552-1.5A
* Not illustrated.
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one
(pair or set) of each part indicated by a bullet (•) for every four tools in service.
¤ The LA1-A550S Angle Housing Assembly is furnished with two Wicks. Use Wick (LA1-561) with the notch on CA200 models.
WARNING
# Always install a Locking Throttle Lever Assembly (6A) on a tool with a Low Profile Concentric Flange (19A). Do not
equip a tool with a standard non-locking Throttle Lever (6) and Low Profile Concentric Flange. This can allow the tool to
continue to run if dropped or set down.
continue to run if dropped or set down.