Справочник Пользователя для Elo TouchSystems 1528L
User Manual: 1528L
SW200095 Rev A, Page 36 of 39
Chapter 9: Regulatory Information
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and
current requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified herein will likely result in
improper operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are
hazardous voltages generated by this equipment which constitute a safety
hazard. Service should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an
integral safety ground wire intended for connection to a grounded safety
outlet.
current requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified herein will likely result in
improper operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are
hazardous voltages generated by this equipment which constitute a safety
hazard. Service should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an
integral safety ground wire intended for connection to a grounded safety
outlet.
1) Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the
safety certification. Modification or misuse can provide a shock hazard
that can result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are
questions about the installation prior to connecting the equipment to
mains power.
Under no circumstances use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the
safety certification. Modification or misuse can provide a shock hazard
that can result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are
questions about the installation prior to connecting the equipment to
mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B
limits for radio noise emissions from digital apparatus as established by the
Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power
cords and interconnecting cabling provided with the equipment. Substitution
of provided cords and cabling may compromise electrical safety or CE Mark
Certification for emissions or immunity as required by the following
standards:
and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B
limits for radio noise emissions from digital apparatus as established by the
Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power
cords and interconnecting cabling provided with the equipment. Substitution
of provided cords and cabling may compromise electrical safety or CE Mark
Certification for emissions or immunity as required by the following
standards:
This Information Technolgy Equipment is required to have a CE Mark on
the manufacturer’s label which means that the equipment has been
tested to the following Directives and Standards:
the manufacturer’s label which means that the equipment has been
tested to the following Directives and Standards: