Manualsbrain.com
  1. Инструкции и руководства
  2. Бренды
  3. JVC
  4. DT-V17L2D
  5. Справочник Пользователя

Справочник Пользователя для JVC DT-V17L2D

Скачать
Страница из 20
14
To assign the functions to the pin terminals
For the operation procedure, see page 7.
1
  Select “REMOTE SETTING” on the SET-UP MENU.
2
  Set “PARALLEL TYPE” to “SET.”
3
  Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want 
to assign.
•  For selectable functions, see the tables below.
Functions controlled by the MAKE/TRIGGER system
*
5
 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen 
(short-circuiting). While controlling with the TRIGGER system, the screen changes as same as when pressing 
SCREENS CHECK button (
☞ page 6).
*
6
 Must be controlled with the TRIGGER system. This function cannot be controlled with the MAKE system.
*
7
 Selects which functions in “AREA MARKER” are activated, non-“R-” items or “R-” items (
☞ page 10).
*
8
 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden 
(opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While 
controlling with the TRIGGER system, the pattern of the audio channel display is switched.
*
9
 Displays the information shown when INPUT SELECT button of the current input is pressed (
☞ “About the Status 
Display” on page 7). While controlling with the MAKE system, the information is displayed only at the moment of short-
circuiting.
•  You cannot assign the same function to different pin terminals.
•  The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and 
opening it.
External Control
7 About the external control
This monitor has three external control terminals.
•  MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.
  (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to 
the GND pin terminal, or disconnecting (opening) it (
☞ below).
  (2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the 
corresponding pin terminal (
☞ below).
•  RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (
☞ “Using the serial 
communication” on page 15)
•  RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system. (
☞ “Using the serial communication” 
on page 15)
Set the following items of “REMOTE SETTING” in SET-UP MENU according to the external control terminal and 
control system (
☞ page 13).
Control terminal
Control system
“SERIAL TYPE” setting
“PARALLEL TYPE” setting
MAKE/TRIGGER 
terminal
MAKE 
—
MAKE
TRIGGER
—
TRIGGER
RS-485 terminal
Serial 
communication 
RS-485
RS485*
1
—
RS-232C terminal
RS-232C
RS232C*
1
—
*
1
 On the monitor connected to the personal computer etc, select the terminal the equipment is actually connected to. On 
other monitors, select “RS485.”
•  Control priority is as follows.
  MAKE > TRIGGER, serial communication, and buttons and menu on the monitor
•  You can use the external control even when “CONTROL LOCK” is set to “ON” (
☞ page 13).
•  When the monitor is off (on standby), external control is not available.
<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated controller*
2
. For the details, see below.
*
2
 The controller is not commercially available. Consult your dealer if you need it.
<Serial communication>
7 Using the MAKE/TRIGGER system
The MAKE/TRIGGER terminal is configured as follows. You can assign a function to each pin terminal in 
“REMOTE SETTING” (
☞ “PIN1, PIN2, PIN3, PIN4, PIN5” on page 13).
•  You cannot change the functions assigned to the pin terminals from 6th to 8th.
PC, etc.
RS-485 IN
or
RS-232C
RS-485 
OUT
RS-485
 IN
RS-485 
OUT
RS-485
 IN
RS-485 
OUT
Display
Functions to be 
controlled
Opening
Short-
circuiting
COMPONENT Changes the input 
to “COMPO.”
Invalid
Valid
VIDEO
Changes the input 
to “VIDEO.”
Invalid
Valid
TALLY SEL
Selects the color of 
the tally lamp.
Green
Red
SOURCE ID
☞ “SOURCE ID” on 
page 13
Off
On
MUTING
Muting on/off
Off
On
MARK.SEL
Selects the items of 
“AREA MARKER”*
7
Non-“R-” 
items
”R-” items
L.METER
Audio level meter 
display
*
8
STATUS
Status display*
9
☞ “About the Status 
Display” on page 7
— — —
No function
—
—
•  See also page 15.
This is a female 
terminal.
Pin No.
Pin name
Pin No.
Pin name
1
PIN1
5
PIN5
2
PIN2
6
PIN6 (TALLY)*
3
3
PIN3
7
PIN7 (ENABLE)
*4
4
PIN4
8
PIN8 (GND)
Display
Functions to be 
controlled
Opening
Short-
circuiting
COLOR OFF Color off
Color
Monochrome
ASPECT
Changes the 
aspect ratio.
4:3
16:9
A.MARKER
The area marker 
display
Off
On
S.MARKER
The safety marker 
display
Off
On
TIME CODE Time code display Off
On
1:1
Displays in 1:1 
mode.
Off
On
SCR CHECK Screens check
*
5
I/P MODE
I/P MODE
*
6
SDI 1
Changes the input 
to “SDI 1.”
Invalid
Valid
SDI 2
Changes the input 
to “SDI 2.”
Invalid
Valid
DVI
Changes the input 
to “DVI.”
Invalid
Valid
*
3
 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is 
invalid).
*
4
 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.
DT-V17L2D_EA_EN_R.indd   14
DT-V17L2D_EA_EN_R.indd   14
07.9.14   7:01:49 PM
07.9.14   7:01:49 PM