Справочник Пользователя для Mitsubishi Electronics MLM400
9
1. Determine the installation location
CAUTION
Installing your LCD display must be done by a qualified technician.
Contact your dealer for more information.
Contact your dealer for more information.
CAUTION
MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY
TWO OR MORE PEOPLE. Failure to follow this caution may result in
injury if the LCD monitor falls.
MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY
TWO OR MORE PEOPLE. Failure to follow this caution may result in
injury if the LCD monitor falls.
IMPORTANT
Lay the protective sheet, which was wrapped around the LCD monitor
when it was packaged, beneath the LCD monitor so as not to scratch
the panel.
Lay the protective sheet, which was wrapped around the LCD monitor
when it was packaged, beneath the LCD monitor so as not to scratch
the panel.
2. Install the remote control batteries
The remote control is powered by 1.5V AA batteries. To install or
replace batteries:
1. Press and slide to open the cover.
2. Align the batteries according to the (+) and (–) indications inside
replace batteries:
1. Press and slide to open the cover.
2. Align the batteries according to the (+) and (–) indications inside
the case.
3. Replace the cover.
CAUTION
Incorrect usage of batteries can result in leaks or bursting. Mitsubishi
recommends the following battery use:
•
recommends the following battery use:
•
Place "AA" size batteries matching the + and - signs on each
battery to the + and - signs of the battery compartment.
battery to the + and - signs of the battery compartment.
•
Do not mix battery brands.
•
Do not combine new and old batteries. This can cause a shorten
life or liquid leakage of batteries.
life or liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery acid from
leaking into the battery compartment. Don't touch exposed bat-
tery acid, it cause damage to your skin.
NOTE:
leaking into the battery compartment. Don't touch exposed bat-
tery acid, it cause damage to your skin.
NOTE:
If you do not intend to use the Remote Control for a
long period, remove the batteries.
3. Connect external equipment
(See page 10-16)
•
To protect the connected equipment, turn off the main power be-
fore making connections.
fore making connections.
•
Refer to your equipment user manual.
4. Connect the supplied power cord
•
The equipment should be installed close to a power outlet and
should be easily accessible.
should be easily accessible.
•
Fully insert the prongs into the power outlet socket. Loose connec-
tion may cause image degradation.
tion may cause image degradation.
5. Switch on the power of all the attached
external equipment
external equipment
When connected to a computer, turn the computer on first.
6. Operate the attached external equipment
Display the signal on the external equipment you wish.
7. Adjust the sound
Make adjustments when adjustment of the volume is required.
8. Adjust the screen (See pages 19-27)
Make adjustments when adjustment of the screen display
position.
position.
9. Adjust the image (See page 19-27)
Make adjustments when picture adjustment such as the brightness or
contrast is required.
contrast is required.
10. When monitor is installed in the portrait
position
position
•
Remove the stand (feet).
•
Left edge should be upper from front view.
11. When installing the monitor to a wall
How to remove the stand
1.
1.
Spread the protective sheet on the flat surface, such as
a desk.
a desk.
2.
Place monitor on the protective sheet.
3.
Remove 2 screws by screwdriver and place them in a safe
place for reuse.
place for reuse.
How to install stand
1.
1.
Please turn monitor off.
2.
Insert claws of monitor to stand holes until clicks.
3.
Fasten 2 screws(M5 x 55mm-top, M5 x 45mm-bottom) on both
sides of the monitor. Torque 280 ~ 300N•cm.
sides of the monitor. Torque 280 ~ 300N•cm.
Setup Procedure
Remove the cover
1
Insert the batteries
Replace the cover
3
2