Справочник Пользователя для Mitsubishi Electronics DX-ZD6UE
6
TEMP ALM terminal
Terminal for informing of high internal temperature.
Terminal for informing of high internal temperature.
FAN ALM terminal
Terminal for informing of abnormality of the fan.
Terminal for informing of abnormality of the fan.
HDD ALM terminal
Terminal for informing of abnormality of the HDD.
Terminal for informing of abnormality of the HDD.
4
EXTERNAL CONTROL switch
Set this switch to ON (left side) to turn on and off the
power of this unit linking with the recorder’s switch.
When not linking with the recorder, set this switch to
OFF (right side).
power of this unit linking with the recorder’s switch.
When not linking with the recorder, set this switch to
OFF (right side).
Notice
•
When the EXTERNAL CONTROL switch is set to ON,
make sure to perform “Connection to link the power
supply of the recorder and this unit” on
make sure to perform “Connection to link the power
supply of the recorder and this unit” on
page 8.
When the recorder is turned on, this unit is turned on
at the same time.
at the same time.
•
It is recommended to link this unit with the recorder
in order to allow the internal hard disks to rest or to
properly handle a problem, if occurs.
in order to allow the internal hard disks to rest or to
properly handle a problem, if occurs.
5
CONT IN terminal
Reserved.
6
CONT OUT terminal
Reserved.
7
SERIAL BUS IN port
Port for connecting with the recorder.
8
SERIAL BUS OUT ports
Ports for connecting with another DX-ZD6UE when
using multiple number of DX-ZD6UE.
using multiple number of DX-ZD6UE.
1
MAIN switch
This is the main power switch. When using this unit,
set this switch to ON.
set this switch to ON.
2
AC power socket
Used to connect the power cord. Earth terminal is used
for safety. Make sure to use the 100 to 240 V plug with
earth for the power of this unit.
for safety. Make sure to use the 100 to 240 V plug with
earth for the power of this unit.
Notice
•
When the power outlet does not have an earth
terminal, ask your dealer for the earth work (pay
service). Never connect the earth terminal of the
power plug to a gas pipe, water pipe, conductor rod,
and so on.
terminal, ask your dealer for the earth work (pay
service). Never connect the earth terminal of the
power plug to a gas pipe, water pipe, conductor rod,
and so on.
•
Use the supplied AC power cord.
•
Make sure to plug this unit into the outlet of the same
power line that is used for the recorder connected.
When this unit is plugged into the outlet of other line,
recording or copying will not be resumed correctly
after a power failure.
power line that is used for the recorder connected.
When this unit is plugged into the outlet of other line,
recording or copying will not be resumed correctly
after a power failure.
3
I/O terminals
CONT IN terminal
Terminal for inputting the power on/off status of the
recorder. Connect this terminal with the DC 12V OUT
terminal on the rear of the recorder.
Terminal for inputting the power on/off status of the
recorder. Connect this terminal with the DC 12V OUT
terminal on the rear of the recorder.
CONT OUT terminal
Terminal for outputting the power on/off status of
the recorder. When using multiple number of HDD
extension units and using the power on/off linkage
function, connect this terminal with the CONT IN
terminal on the rear of the HDD extension unit to be
connected.
Terminal for outputting the power on/off status of
the recorder. When using multiple number of HDD
extension units and using the power on/off linkage
function, connect this terminal with the CONT IN
terminal on the rear of the HDD extension unit to be
connected.
GND terminals
They are the common GND terminals. When using the
power on/off linkage function, connect this terminal
with the GND terminal on the rear of the recorder.
They are the common GND terminals. When using the
power on/off linkage function, connect this terminal
with the GND terminal on the rear of the recorder.
1
3
5
6 7
8
4
2
Rear view
Major operations and their functions (continued)