Листовка для AMX MAX-AOM

AMX Corporation reserves the right to alter specifications without notice at any time.

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2178-55

REV: B

As a result, the AOM connected to USB port 2 will switch from providing audio
output/zones 5-8 to providing audio output/zones 1-4, the next time the server is
rebooted.

Mounting the MAX-AOM

Note: Static electricity can damage electronic circuitry. Before mounting the AOM(s),
discharge any accumulated static electricity from your body and screwdriver by
touching a grounded metal object.

The MAX-AOM includes hardware for mounting the unit in a standard 19” equipment
rack. A single AOM takes up one-half of the width of a single rack unit, so you can
mount two AOMs side by side in a single RU by using the (optional) AOM-EX
Expansion Kit (FG 2178-56). Refer to the next page for details.

Using the AOM-EX Expansion Kit

The optional AOM-EX Expansion Kit (FG 2178-56) includes a MAX-AOM, a Side
Mounting Bracket, Short Rack-Mounting Bracket, and mounting hardware (FIG. 2).
Use the Expansion Kit to mount a second AOM next to the first one, in a single rack
space.

The Side Mounting Bracket uses a set of six screws to connect to bracket to the side
panel of AOM #1. The bracket features tabs to ensure proper positioning and
alignment of the two AOMs, and four screws (two on the front and two on the rear) to
secure the AOM #1/side bracket assembly to AOM #2.

The Short Rack-Mounting Bracket uses three screws to attach to the AOM #2
enclosure, and two screws to secure the left side of the MAX-AOM-EX assembly to
the equipment rack.

FIG. 3 describes using the MAX-AOM-EX kit:

Notice: MAX Products are not designed or intended to, and may not be used to,
violate anyone’s copyright or other intellectual property rights. Each user of the MAX
Products may only use the Products in connection with materials legally owned or
licensed by such user and only to the extent such ownership or license rights permit
such use.

FIG. 2

MAX-AOM-EX brackets

Tabs fit into slots on the

side panel of the AOM #2

Tabs fit into slots on the
side panel of AOM #1

Two screws secure the bracket to front and back of AOM #2

Use screws to secure the Side Mounting Bracket to AOM #1

Short Rack-Mount Bracket

Two screws secure the Short Rack-
Mount Bracket to the

Three screws secure the

Short Rack-Mount Bracket

to the side of AOM #2

Use screws to secure the Side Mounting Bracket to AOM #1

Side Mounting Bracket

equipment rack

FIG. 3

Using the optional MAX-AOM-EX Expansion Kit to mount two AOMs in a

single rack space.

(front)

Remove the Faceplate

Use the tabs on the Side Mounting Bracket to position and connect the AOMs

Replace the Faceplate

AOM #1

Secure the AOM #1/side bracket assembly to AOM #2 using the supplied screws.

Two screws in the front and two in the back secure the Side Mounting Bracket to the

(front)

AOM #1

Remove and discard the long

AOM #2 enclosure.

Use three screws to attach the Short Rack-Mount Bracket to the front left side of
AOM #2, then secure the short bracket/AOM #2 assembly to the equipment rack with
two screws (on the front of the bracket).

(front)

rack-mount bracket.

Side Mounting Bracket

(front)

AOM #2

AOM #1

Position the SIde Mounting Bracket to AOM #1, using the tabs to ensure
proper positioning, Use six of the supplied screws to secure the

These mounting surfaces (on front and rear of
the bracket) secure the AOM #1/bracket
assembly to AOM #2

Side Mounting Bracket to AOM #1.

Rack-Mount

Short

Bracket