Листовка для Digi 91000611D
91000611D
SYNC/570i (PCI) Installation Card
SYNC/570i
Features
•
Line speeds: to 5Mbps—EIA-530/X.21
to 2.5 Mbps—V.35
to 90 Kbps—Synch. EIA-232
to 144 Kbps—Async. EIA-232
to 90 Kbps—Synch. EIA-232
to 144 Kbps—Async. EIA-232
•
Full modem control
•
DMA channels for full duplex operation
•
16KB or Full 256KB shared memory window
•
Software configurable
•
SurgeBlock surge protection
Specifications
Power
•
•
1.5 A @ +5 VDC
•
50 mA @ +/- 12 VDC
Environmental
•
•
Temperature:
10
°
C to 55
°
C
•
Relative Humidity:5% to 90%, non-condensing
•
SurgeBlock:
Standard
Copyright
Digi International Inc. 1997 All Rights Reserved
The Digi logo is a trademark of Digi International Inc. All other brand and
product names are the trademarks of their respective holders.
product names are the trademarks of their respective holders.
Information in this document is subject to change without notice and does
not represent a commitment on the part of Digi International.
not represent a commitment on the part of Digi International.
Digi provides this document “as is,” without warranty of any kind, either
expressed or implied, including, but not limited to, the implied warranties
of fitness or merchantability for a particular purpose. Digi may make
improvements and/or changes in this manual or in the product(s) and/or the
program(s) described in this manual at any time.
expressed or implied, including, but not limited to, the implied warranties
of fitness or merchantability for a particular purpose. Digi may make
improvements and/or changes in this manual or in the product(s) and/or the
program(s) described in this manual at any time.
This product could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
may be incorporated in new editions of the publication.
Changes are periodically made to the information herein; these changes
may be incorporated in new editions of the publication.
Two-port Universal
Interface Card for
SYNC/570i (PCI)
Synchronous Communications
Controller
Installation Instructions
Introduction
Digi's two port Universal Interface Card can auto-
matically determine, from the cable, the interface
bus type to use with the peripheral device. That is,
you can select an interface type for the adapter
(V.35, X.21, EIA-530, or EIA-232) just by connect-
ing the appropriate cable between the adapter and
the peripheral device. Each of the ports on the
daughter card can use the same or a different type of
interface cable, giving you the flexibility to use one
adapter to connect to peripherals with two different
interface types.
matically determine, from the cable, the interface
bus type to use with the peripheral device. That is,
you can select an interface type for the adapter
(V.35, X.21, EIA-530, or EIA-232) just by connect-
ing the appropriate cable between the adapter and
the peripheral device. Each of the ports on the
daughter card can use the same or a different type of
interface cable, giving you the flexibility to use one
adapter to connect to peripherals with two different
interface types.
Figure 1: SYNC/570i and Universal Interface Card
Installing the Adapter
Before you begin
Before installing the SYNC/570i adapter and daugh-
ter card, you should do the following:
•
ter card, you should do the following:
•
Be sure that you have the correct cables for the
interface type(s) you will use with the SYNC/
570i. Depending on the package you ordered,
you will have one or two cables.
interface type(s) you will use with the SYNC/
570i. Depending on the package you ordered,
you will have one or two cables.
•
Record the adapter’s serial number (located
under the part number label as shown in
Figure 1), which will enable Digi to provide you
with better service, should the need arise.
under the part number label as shown in
Figure 1), which will enable Digi to provide you
with better service, should the need arise.
•
Unplug power from the PC.
•
Discharge static electricity from your body by
touching a grounded surface (prior to handling
the adapter).
touching a grounded surface (prior to handling
the adapter).
•
Put a ground strap on to ground yourself. (If one
is not available, ground yourself by touching an
unpainted metal surface, such as the computer’s
chassis.)
is not available, ground yourself by touching an
unpainted metal surface, such as the computer’s
chassis.)
Installation Procedure
1. Install the adapter.
a. Remove the computer’s cover.
b. Locate an available PCI slot in your computer
b. Locate an available PCI slot in your computer
and remove the slot plate.
c. Insert the adapter into the slot and screw the
endplate to the computer chassis. The endplate
must be screwed into the computer chassis to
remain in compliance with Part 15 of FCC
rules.
must be screwed into the computer chassis to
remain in compliance with Part 15 of FCC
rules.
d. Replace the computer’s cover.
2. Connect cables. One end of each cable is
labelled with the interface type. Attach that end
to the peripheral. Attach the other end to an
adapter port. (Additional cabling information is
provided on this card.)
to the peripheral. Attach the other end to an
adapter port. (Additional cabling information is
provided on this card.)
3. Boot the computer.
4. Run Digi’s diagnostics program.
4. Run Digi’s diagnostics program.
The SYNC/570i PCI diagnostics are supplied on a
diskette that is shipped with the adapter. You
should run the diagnostics to verify that you can
communicate with the peripheral devices. Refer to
the text file on the diskette for information on
using the diagnostics.
diskette that is shipped with the adapter. You
should run the diagnostics to verify that you can
communicate with the peripheral devices. Refer to
the text file on the diskette for information on
using the diagnostics.
Note: The LEDs showing through the faceplate
on the adapter will not light until a driver
is loaded and the adapter initialized. With
the Digi driver loaded, the green LED will
light to indicate that the adapter is in a
“ready” state. The amber LED will light
when data is passed to the peripheral
device.
is loaded and the adapter initialized. With
the Digi driver loaded, the green LED will
light to indicate that the adapter is in a
“ready” state. The amber LED will light
when data is passed to the peripheral
device.
What next?
Install and configure the software for the Digi
SYNC/570i PCI adapter.
SYNC/570i PCI adapter.
Usage Note
•
If you change the interface of a port (by chang-
ing the interface cable) while your system is up,
the new interface may not be recognized until
the driver is restarted.
ing the interface cable) while your system is up,
the new interface may not be recognized until
the driver is restarted.
If you have a problem
•
If you have difficulty communicating with a
peripheral connected to your SYNC/570i
adapter, call Digi Support Services to obtain a
diagnostic to use, and assistance in using it.
peripheral connected to your SYNC/570i
adapter, call Digi Support Services to obtain a
diagnostic to use, and assistance in using it.
•
If you have a problem booting your system after
installation of your SYNC/570i adapter, you
should call Digi Support Services for assistance.
installation of your SYNC/570i adapter, you
should call Digi Support Services for assistance.