Справочник Пользователя для Fortinet 5103b
FortiController-5103B system
Front panel LEDs and connectors
FortiController-5103B Session-Aware Load Balancer Guide
10-500-161552-20140822
10-500-161552-20140822
7
Front panel LEDs and connectors
From the FortiController-5103B font panel you can view the status of the board LEDs to
verify that the board is functioning normally. You also connect the FortiController-5103B
board to your 10-gigabit network using the 1 to 8 front panel SFP+ connectors. The front
panel also includes B1 and B2 connectors for the base channels, an Ethernet
management interface (MGMT), an RJ-45 console port for connecting to the
FortiController-5103B CLI and a USB port. The USB port can be used with any USB key
for backing up and restoring configuration files.
verify that the board is functioning normally. You also connect the FortiController-5103B
board to your 10-gigabit network using the 1 to 8 front panel SFP+ connectors. The front
panel also includes B1 and B2 connectors for the base channels, an Ethernet
management interface (MGMT), an RJ-45 console port for connecting to the
FortiController-5103B CLI and a USB port. The USB port can be used with any USB key
for backing up and restoring configuration files.
LEDs
FortiController-5103B front panel interfaces F1 to F8 appear on the
FortiController-5103B web-based manager and CLI as interfaces f1 to f8. In single
FortiController-5103B mode, workers see these as fctrl/1 to fctrl/8. In dual
FortiController-5103B mode, workers see these as fctrl1/1 to fctrl1/8 and fctrl2/1 to
fctrl2/8.
FortiController-5103B web-based manager and CLI as interfaces f1 to f8. In single
FortiController-5103B mode, workers see these as fctrl/1 to fctrl/8. In dual
FortiController-5103B mode, workers see these as fctrl1/1 to fctrl1/8 and fctrl2/1 to
fctrl2/8.
Table 2: FortiController-5103B LEDs
LED
State
Description
Fabric
(1/2 to 14)
(1/2 to 14)
Green
Fabric backplane interface is connected at 10 Gbps or 1
Gbps. Backplane Fabric interface slot-14 is not
accessible.
Gbps. Backplane Fabric interface slot-14 is not
accessible.
Flashing
Green
Green
Network activity at the fabric backplane interface.
Off
No link is established.
Base (1/2 to 14)
Green
Base backplane interface is connected at 1 Gbps.
Flashing
Green
Green
Network activity at the base backplane interface.
Off
No link is established.
OOS
(Out of Service)
(Out of Service)
Off
Normal operation.
Amber
A fault condition exists and the FortiController-5103B
blade is out of service (OOS). This LED may also flash
very briefly during normal startup.
blade is out of service (OOS). This LED may also flash
very briefly during normal startup.
PWR (Power)
Green
The FortiController-5103B board is powered on.
STA (Status)
Off
The FortiController-5103B board is powered on.
Flashing
Green
Green
The FortiController-5103B is starting up. If this LED is
flashing at any time other than system startup, a fault
condition may exist.
flashing at any time other than system startup, a fault
condition may exist.
ACC (Disk
activity)
activity)
Off or
Flashing
green
Flashing
green
The ACC LED flashes green when the
FortiController-5103B board accesses the flash disk. The
flash disk stores the current firmware build and
configuration files. The system accesses the flash disk
when starting up, during a firmware upgrade, or when an
administrator is using the CLI or GUI to change the
FortiController-5103B configuration. Under normal
operating conditions this LED flashes occasionally, but is
mostly off.
FortiController-5103B board accesses the flash disk. The
flash disk stores the current firmware build and
configuration files. The system accesses the flash disk
when starting up, during a firmware upgrade, or when an
administrator is using the CLI or GUI to change the
FortiController-5103B configuration. Under normal
operating conditions this LED flashes occasionally, but is
mostly off.