Справочник Пользователя для Toshiba B-SX4T
APPENDIX 1 MESSAGES AND LEDS
ENGLISH VERSION EO1-33058
APPENDIX 1 MESSAGES AND LEDS
EA1- 1
APPENDIX 1 MESSAGES AND LEDS
Appendix 1 describes the LCD messages displayed on the operation panel.
Symbols in the message
1: : The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2: ****: the number of unprinted media. Up to 9999 (in pieces)
3: %%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4: ###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5: &&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
Symbols in the message
1: : The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2: ****: the number of unprinted media. Up to 9999 (in pieces)
3: %%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4: ###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5: &&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
LED Indication
No.
LCD Message
POWER ONLINE ERROR
Printer Status
Restoration by
RESTART key
Yes/No
Acceptance of
Status Request
Reset Command
Yes/No
ON LINE
z In online mode
-----
Yes
1
ON LINE
~
z In online mode (The printer in
communication)
----- Yes
2
HEAD OPEN
z
z The print head block is opened in online
mode.
----- Yes
3
PAUSE ****
z
z The printer is paused.
Yes
Yes
4
COMMS ERROR
z
A parity, overrun, or framing error has
occurred during communication through
the RS-232C.
occurred during communication through
the RS-232C.
Yes Yes
5
PAPER JAM ****
z
The media is jammed during paper feed.
Yes
Yes
6
CUTTER ERROR****
z
A problem has occurred with the cutter
module.
Yes Yes
7
NO PAPER ****
z
The media has run out, or the media is
not loaded properly.
Yes Yes
8
NO RIBBON ****
z
The ribbon has run out.
Yes
Yes
9
HEAD OPEN ****
z
Feed or printing was attempted with the
print head block open.
Yes Yes
10
HEAD ERROR
z
There is a problem with the print head.
Yes
Yes
11
EXCESS HEAD TEMP
z
The print head is overheated.
No
Yes
12
RIBBON ERROR****
z
The ribbon has been torn. A problem
has occurred with the sensor that
determines the torque for the ribbon
motor.
has occurred with the sensor that
determines the torque for the ribbon
motor.
Yes Yes
13
REWIND FULL ****
z
An overflow error has occurred in the
rewinder unit.
Yes Yes
14
SAVING%%%%%%%
or
SAVING ###&&&&
or
SAVING ###&&&&
z
In writable character or PC command
save mode
save mode
----- Yes
15
FLASH WRITE ERR.
z
An error has occurred while writing to
flash memory or ATA card.
No Yes
16
FORMAT ERROR
z
An erase error has occurred in
formatting the flash memory or ATA
card.
formatting the flash memory or ATA
card.
No Yes
17
FLASH CARD FULL
z
Data cannot be stored because the flash
memory or ATA card is full.
No Yes
18
Display of error
message (See Notes.)
message (See Notes.)
z
A command error has occurred in
analyzing the command.
Yes Yes
19
POWER FAILURE
z
A power failure has occurred.
No
No
20
INTIALIZING…
z
z A flash memory card is being initialised.
-----
-----
21
EEPROM ERROR
z
Data cannot be read from/written to a
backup EEPROM properly.
----- -----