Справочник Пользователя для Toshiba B-SX4T
2. PRINTER SETUP
ENGLISH VERSION EO1-33058
2.9 Setting an Operating Environment
E2-14
2.9 Setting an Operating
Environment
Depending on the settings of your host computer or an interface to be
used, it may be necessary to change the printer parameter settings.
Follow the procedures described below to change the printer parameter
settings in the System Mode to correspond to your environment.
used, it may be necessary to change the printer parameter settings.
Follow the procedures described below to change the printer parameter
settings in the System Mode to correspond to your environment.
How to enter the System Mode
1. Turn on the printer and confirm that “ONLINE” appears on the LCD
1. Turn on the printer and confirm that “ONLINE” appears on the LCD
Message Display.
2. Press the [PAUSE] key to pause the printer.
3. Hold down the [RESTART] key for three seconds until “<1>RESET”
3. Hold down the [RESTART] key for three seconds until “<1>RESET”
is displayed.
The System Mode consists of the following menus.
<1>RESET
This menu is used to clear print data sent from a
PC and return the printer to an idle state.
Refer to Section 3.3 Reset.
PC and return the printer to an idle state.
Refer to Section 3.3 Reset.
<2>PARAMETER SET
This menu is used to set the printer parameters.
Refer to Section 2.9.1 Parameter Setting.
Refer to Section 2.9.1 Parameter Setting.
<3>ADJUST SET
This menu is used to make a fine adjustment of a
print start position, cut position, etc.
Refer to Section 2.12 Position and Print Tone
Fine Adjustment.
print start position, cut position, etc.
Refer to Section 2.12 Position and Print Tone
Fine Adjustment.
<4>DUMP MODE
This menu is used to print the data in the receive
buffer for debug.
Refer to Section 2.9.2 Dump Mode Setting.
buffer for debug.
Refer to Section 2.9.2 Dump Mode Setting.
<5>EXPAND MODE
This menu is used to start the program for
BASIC mode.
Refer to Section 2.9.3 BASIC Expansion
Mode.
BASIC mode.
Refer to Section 2.9.3 BASIC Expansion
Mode.
NOTE:
Incorrect settings can cause the printer to function erroneously. If you
have any problems with the parameter settings, please contact your nearest
TOSHIBA TEC service representative.
For the settings this manual does not cover, please contact your nearest
TOSHIBA TEC service representative, or refer to the B-SX4T/SX5T Series
Key Operation Specification stored in the CD-ROM.
have any problems with the parameter settings, please contact your nearest
TOSHIBA TEC service representative.
For the settings this manual does not cover, please contact your nearest
TOSHIBA TEC service representative, or refer to the B-SX4T/SX5T Series
Key Operation Specification stored in the CD-ROM.
NOTES:
1. System Mode menus can be selected with the [RESTART] or [FEED] key.
2. To enter each of the above System Mode menus, press the [PAUSE] key
2. To enter each of the above System Mode menus, press the [PAUSE] key
when the menu is displayed.
3. If the [PAUSE] key is pressed with “<1>RESET” being displayed, the
printer will turn to an idle state and the message will change to “ONLINE”.
[FEED]
[FEED]
[FEED]
[FEED]
[FEED]
[RESTART]
[RESTART]
[RESTART]
[RESTART]
[RESTART]
<1>RESET
<2>PARAMETER SET
<3>ADJUST SET
<4>DUMP MODE
<5>EXPAND MODE
ON LINE
PAUSE
[PAUSE]
Hold down
[RESTART] for 3 sec.
LCD Message
Display
Display
FEED key
RESTART key
PAUSE key