Справочник Пользователя для Zebra Technologies P640i
![Zebra Technologies](https://files.manualsbrain.com/attachments/a78f49d565a2596a8b31f4240e25fed2998da2a0/common/fit/150/50/2656e56263d759e2c7910989c000585d7bce0fb5d50f1f63705e38675fa7/brand_logo.gif)
46
P640i Card Printer User Guide
980541-001 Rev. A
8. When you are satisfied with the graytone image
quality, print one or two cards with
Wedge_1.bmp
to test for ribbon wrinkling. This image is the
densest possible process black, meaning that on
all three passes (Y, M and C) one end of the
printhead is fully “on”, while the other end is
“off”, a sure way to induce wrinkling if there is
the slightest tendency. Wrinkling may be a head
angle issue (more clockwise than it should be),
but it may equally result from too high a ribbon
torque, page TN4-x.
densest possible process black, meaning that on
all three passes (Y, M and C) one end of the
printhead is fully “on”, while the other end is
“off”, a sure way to induce wrinkling if there is
the slightest tendency. Wrinkling may be a head
angle issue (more clockwise than it should be),
but it may equally result from too high a ribbon
torque, page TN4-x.
Check the torque before readjusting
the head
.
9. When you are satisfied that ribbon wrinkling is
under control, print one or two cards with
Wedge_2. bmp
, this being the same triangle flipped
so that its black area starts full width.
10. As a final test, run Portraits.bmp to test for skin
tone realism, etc.
Print Station Parameters in the
Driver
Start
> Printers (or Printers and Faxes) > Right click
Zebra P640i > Properties > Device Settings > Status >
Advanced (Information)
See also:
Start
> Printers (or Printers and Faxes) >
Right click Zebra P640i > Properties > Device
Settings > Control > Advanced Utilities >
Settings > Control > Advanced Utilities >
Show Sensor
Data
Ribbon Panel Detect: The current reading of the
color ribbon sensor (High = black, Low = not black).
color ribbon sensor (High = black, Low = not black).
Panel Threshold: The current value of the
detection threshold for the color ribbon. Above this
value is termed “black”, below this value is termed
“not black”.
detection threshold for the color ribbon. Above this
value is termed “black”, below this value is termed
“not black”.
Ribbon Encoder Count: The pulse count from the
motion sensor (following page) from start to finish of
the most recent YMCK panel set paid out from the
ribbon supply roll.
motion sensor (following page) from start to finish of
the most recent YMCK panel set paid out from the
ribbon supply roll.
Printhead Voltage: Should be about 24V.
Printhead Temperature: Temperature ceiling
70°C (above that temperature, printing is stopped until
the head cools)
70°C (above that temperature, printing is stopped until
the head cools)
Printhead Lift
(logic states): 0 = head raised, 1 =
head down (see photos on following page)
Start
> Printers (or Printers and Faxes) > Right click
Zebra P640i > Properties > Device Settings >
Printer
Adjustment
Horizontal (X) Offset (Pixels): Moves the image
along the length of the card. Used to center the image
on the card.
along the length of the card. Used to center the image
on the card.
Vertical (Y) Offset (Pixels): Moves the image up
and down. Used to center the image on the card.
and down. Used to center the image on the card.
Black Panel - Speed : The printer was
characterized in manufacture at a specific speed.
Changing this speed will force the printer to use
estimated energy values, and is not recommended.
characterized in manufacture at a specific speed.
Changing this speed will force the printer to use
estimated energy values, and is not recommended.