Справочник Пользователя для Mitsubishi Electronics XD95U
EN-29
ENGLIS
H
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea
level, and temperature is between 0°C–35°C.
level, and temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 0°C and 35°C. The
projector will be over cooled, if you turn the mode on under such condition.
projector will be over cooled, if you turn the mode on under such condition.
To activate the High Altitude Mode:
1.
Press MENU and then press
/
until the SYSTEM SETUP:
Advanced menu is highlighted.
2.
Press
to highlight High Altitude Mode and press
/
to select On.
A confirmation message displays.
3.
Highlight Yes and press MODE/ENTER.
Operation under "High Altitude Mode" may cause a higher decibel operating
noise level because of increased fan speed necessary to improve overall system
cooling and performance.
noise level because of increased fan speed necessary to improve overall system
cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down
symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to
High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any
and all harsh or extreme conditions.
symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to
High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any
and all harsh or extreme conditions.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect
the projection settings, operation, or performance.
the projection settings, operation, or performance.
•
Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the
OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second
increments. Use
OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second
increments. Use
/
to select a suitable time frame.
•
Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five
locations. Use
locations. Use
/
to select a preferred position.
•
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use
/
to
select your language.
•
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during
projector start-up. Use
projector start-up. Use
/
to select a screen.
Shutting down the projector
1.
Press
Power and a confirmation message displays prompting you.
If you don't respond in a few seconds, the message will disappear.
2.
Press
Power a second time. The POWER indicator light flashes
orange, the projection lamp shuts down, and the fans will continue to run
for approximately 90 seconds to cool down the projector.
for approximately 90 seconds to cool down the projector.
3.
Once the cooling process finishes, the POWER indicator light is a
steady orange and fans stop.
steady orange and fans stop.
4.
Disconnect the power cord from the wall socket if the projector will not
be used in an extended period of time.
be used in an extended period of time.
•
To protect the lamp, the projector will not respond to any commands during the
cooling process.
cooling process.
•
To shorten the cooling time, you can also activate the Quick Cooling function.
See
See
for details.
•
Do not unplug the power cord before the projector shutdown sequence is
complete or during the 90-second cooling down process.
complete or during the 90-second cooling down process.
•
If the projector is not properly shut down, to protect the lamp, when you attempt
to re-start the projector, the fans will run for a few minutes to cool down. Press
to re-start the projector, the fans will run for a few minutes to cool down. Press
Power again to start the projector after the fans stop and the POWER
indicator light turns orange.
I
I
I
I
I
I