Справочник Пользователя для Mitsubishi Electronics FD730U

EN-33

You can display your desired image as the startup screen (or splash 
screen). Using the menu, you can also use such image as a back-
ground that is displayed while the video is muted or no signal is sup-
plied.

•

You can’t set IMAGE CAPTURE when PASSWORD FUNCTION in 

the FEATURE menu has been set to SPLASH ID SCREEN to 
enable the password lock.

•

You can’t set IMAGE CAPTURE when the component video signal 

is inputted.

1.

Press the COMPUTER button to select the image supplied to 
the COMPUTER/COMPONENT VIDEO IN terminal.

2.

Display your desired image.

3.

Display the INSTALLATION menu.

4.

Select IMAGE CAPTURE by pressing the   or   button.

5.

Press the ENTER button.
•

The setting menu will be displayed.

(Set the background color only when you set the image size to x1 or 
x4.)
6.

Select BACK COLOR by pressing the   or   button.

7.

Select your desired color for the background (GRAY, RED, 
GREEN, BLUE, BLACK, WHITE, RED50%, GREEN50%, or 
BLUE50%) by pressing the   or   button.

8.

Select SIZE by pressing the   or   button.

9.

Select x1, x4, or FULL by pressing the   or   button.

10. Select CAPTURE by pressing the   or   button.
11. Press the ENTER button.

•

A red frame appears. (The size of the red frame is 640 x 360 

pixels.)

12. Adjust the size of the image to be captured so that such image 

stays within the red frame.
•

Press the  ,  ,   or   button to move the red frame.

•

You can’t move the red frame outside the screen.

13. Press the ENTER button twice.

•

Image capture will start.

•

Press the MENU button to cancel the procedure.

•

When the image capture completes, the captured image will 

be displayed for a few seconds.

•

You can’t change the new startup screen back to the original star-

tup screen. (Even when you select RESET ALL in the FEATURE 
menu, the factory default screen isn’t available any longer.) When 
you want to change the startup screen again, capture another 
image.

•

The captured image will be displayed from the next startup. If the 

captured image isn’t displayed, make sure that the setting of 
SPLASH SCREEN in the INSTALLATION menu isn’t OFF. (See 
page 23.)

•

To display the captured image while the video is muted, set AV 

MUTE MODE in the INSTALLATION menu to IMAGE. (See page 
23.)

•

When BACK COLOR in the INSTALLATION menu is set to 

IMAGE, the captured image will be displayed while no signal is 
supplied.

•

In the mute mode, or when no signal is input, it takes longer time 

to display the captured image.

•

Some images can’t be captured correctly because of their signal 

type.

You can split the screen in two and display a computer image on the 
left screen and a video image on the right screen.

1.

Display the FEATURE menu.

2.

Select SPLIT by pressing the   or   button.

3.

Press the ENTER button.
•

The screen is split in two and the left and right screens dis-

play the following images:
-  Left screen:  Image supplied to the last selected input 

source, COMPUTER1, COMPUTER2, or 
HDMI

-  Right screen: Image supplied to the last selected input 

source, VIDEO or S-VIDEO

•

When you press the MENU button, the screen is displayed in 

the normal mode.

•

In the split mode, audio of the left screen is output.

•

In the split mode, the picture quality settings of the input 

source in the normal mode to be displayed on the left screen 
are reflected on the entire screen.

•

When no signal is input, a blue screen is displayed.

•

When you input an interlace signal to the left screen, the dis-

played image may shake up and down slightly, but this is not 
a malfunction.

x1

x4

FULL

CAPTURING IMAGE !

Left screen

Right screen