Справочник Пользователя для Mitsubishi Electronics HC5000

5

[Example 1]

When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation
marks are ASCII codes.):

Sending commands

Status code from

Description

from the PC, etc.

the projector

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D

Command for setting the

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '

'

picture control

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D

Command receipt confirmation

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '

'

(Command echo back)

Sending commands

Status code from

Description

from the PC, etc.

the projector

30 30 41 50 4F 4E 31 0D

Command for setting the

'0' '0' 'A' 'P' 'O' 'N' '1' '

'

AUTO POWER ON to ON

30 30 41 50 4F 4E 31 0D

Command receipt confirmation

'0' '0' 'A' 'P' 'O' 'N' '1' '

'

(Command echo back)

[Example 3]

When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed
in quotation marks are ASCII codes.):

Sending commands

Status code from

Description

from the PC, etc.

the projector

30 30 53 0D

Command for checking

'0' '0' 'S' '

'

the TINT setting

30 30 53 2B 31 30 0D

Check result (+10)

'0' '0' 'S' '+' '1' '0' '

'

• To set TINT at 0,  enter +00. (-00 is invalid.)

[Example 4]

When setting the REFERENCE of GAMMA MODE-USER1 to CINEMA (+2), ADJUST MODE
to RED (R), HIGH to -2, MID to +3 and LOW to 0. (Figures and symbols enclosed in quotation
marks are ASCII codes.):
* There is no command for selecting ALL for ADJUST MODE. Even when you want to set all

the three colors to the same value, send a command for each of R, G, and B respectively.

Sending commands

Status code from

Description

from the PC, etc.

the projector

30 30 47 53  55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD

Command for setting GAMMA

'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '

'

MODE-USER1

30 30 47 53  55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD Command receipt confirmation

'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '

'

(Command echo back)

[Example 2]

When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0,
and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII
codes.):

Use the ASCII or HEX code as shown below to set the value.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

*1

) Setting range differs depending on the input signals.

• Some commands are not executed depending on the input signal. The operational restrictions same as

those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

ITEM

ASCII

HEX

VALUE

CLAMP POSITION

CLP

43h

4Ch

50h

001 - 255

CLAMP WIDTH

CLW

43h

4Ch

57h

01 - 63

VERT.SYNC.

VSC

56h

53h

43h

0 (OFF), 1 (AUTO)

LPF

LPF

4Ch

50h

46h

0 (OFF), 1 (ON)

SHUTTER(U)

SHU

53h

48h

55h

SHUTTER(L)

SHL

53h

48h

4Ch

SHUTTER(LS)

SHLS

53h

48h

4Ch

53h

SHUTTER(RS)

SHRS

53h

48h

52h

53h