Листовка для StarTech.com ET91000SC2

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

This  manual  may  make  reference  to  trademarks,  registered  trademarks,  and  other  protected  names  and/or  symbols  of  third-party  companies  not  related  in  any  way  to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)

to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all

trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access

our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned

for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,

consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow

the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

IEEE 802.3ab, IEEE 802.3z

1 x RJ45 Ethernet

female

2 x LC Fiber female

1 x DC Power

1 x RJ45 Ethernet

female

2 x SC Fiber female

1 x DC Power

Multi Mode

850 nm

550 m (1804 ft)

Full/Half

Yes (Ethernet)

12V DC, 1000mA, center positive,

type M plug

< 4W

Metal

0°C ~ 60°C (32°F ~ 140°F)

-10°C ~ 70°C (14°F ~ 158°F)

10% ~ 90% RH

160.0mm x 95.0mm x 20.0mm

600g

PWR

Power

ON

Unit is powered

OFF

Unit is not powered

RPF

Remote

Power Failure

ON

Remote Power Fail

OFF

Remote Power Normal

LNK

Fiber Link

ON

Fiber link is detected

OFF

Fiber link is not detected

Blink

Fiber activity

LFP

Link Fault

Pass-through

ON

LFP Mode enabled

OFF

LFP Mode disabled

Ethernet Duplex mode will be configured for Full or Half.

Link Fault Pass-through will pass a link failure to the Ethernet

side, if a link failure is encountered on the fiber side and vice

versa. Otherwise, the Ethernet side will continue to show no

link failures, even if the fiber side has no link.

(OFF = Not active, On = Active)

Auto negotiate duplex mode, or force Full/Half via DIP

switches.