Справочник Пользователя для Avaya M770
Chapter 6
Managing Virtual Ports
60
Avaya M770 ATM Switch User’s Guide
Listing the status information for all virtual ports
You can view the status information for all virtual ports on a module or for a
specific virtual port.
Any virtual port information that is marked with an asterisk (*) has been learned by
the M770 ATM Switch during the ILMI dialogue with the remote device.
Information that is not marked with an asterisk has either been configured by the
user or is the default setting for the virtual port.
To view the virtual port status, enter the
specific virtual port.
Any virtual port information that is marked with an asterisk (*) has been learned by
the M770 ATM Switch during the ILMI dialogue with the remote device.
Information that is not marked with an asterisk has either been configured by the
user or is the default setting for the virtual port.
To view the virtual port status, enter the
vport show status
command.
Poll Mode
ILMI polling is used to verify that the same end-station remains
attached at a given port. There are two methods that can be
used:
• check the ESI has not changed. This is referred to as “Port +
attached at a given port. There are two methods that can be
used:
• check the ESI has not changed. This is referred to as “Port +
ESI”.
• check that the system up-time has not changed by a
significant amount. This is referred to as “SysUpTime”.
Multi Reg
This specifies whether multiple ILMI registration is enabled or
not on the virtual port.
not on the virtual port.
Strict AAL
Trans.
Trans.
This specifies whether the translation of the AAL parameter,
that is between UNI 3.0, IISP 3.0, UNI 3.1 and IISP 3.1 should be
OFF, Normal or Strict.
that is between UNI 3.0, IISP 3.0, UNI 3.1 and IISP 3.1 should be
OFF, Normal or Strict.
Sig. SSCOP
Rx. Window
Rx. Window
This parameter is reserved for future use.
All ports are set to the default parameter.
All ports are set to the default parameter.
Wait for Peer
SSCOP
SSCOP
This specifies whether this vport will wait indefinitely for an
incoming QSAAL connection.
incoming QSAAL connection.
Command:
M15-155s8:/>vport show status [<vport id>]
Parameter:
<vport
id>
The virtual port.
This is displayed in the format <slot>.<port>.<virtual port number>.
If a <vport number> parameter is not supplied then the link status summary
information is supplied for all virtual ports.
This is displayed in the format <slot>.<port>.<virtual port number>.
If a <vport number> parameter is not supplied then the link status summary
information is supplied for all virtual ports.
Example:
M15-155s8:/>vport show status
Output:
Virtual Port Status Information
Virtual AdminOperStackUserQ.SAALQ.2931PNNI-HelloILMIILMI
Port Id StateStateType/NetStateStateStateVerState
8.0.0
Virtual AdminOperStackUserQ.SAALQ.2931PNNI-HelloILMIILMI
Port Id StateStateType/NetStateStateStateVerState
8.0.0
UpUp
InternalUserUpUpDown4.0Disabled
8.1.0
UpDown PNNI 1.0NetDownDownDown4.0Inactive
8.2.0
UpUp
UNI 3.1*Net*UpUpDown3.x*Ready
8.3.0
UpUp
UNI 4.0*Net*UpUpDown4.0*Ready
8.4.0
UpUp
PNNI 1.0*Net*UpUpUp4.0* InterSwitch
Table 6.2
Output from the vport show config command
Field
Description