Справочник Пользователя для Grizzly G0514X
<%*&)M$"M'$"M'7$"M(B[\#H^cXZ'$&'
"(("
Figure 53.
9daaVgW^aa[daYZYil^XZidbV`ZVc
Veegdm^bViZ%#%&+\Vj\Z#
Note: For a quick gauge, fold a dollar bill in half
twice (four thicknesses of a dollar bill is approxi-
mately 0.016") and place it between the support
bearing and the blade, as shown in Figure 53
twice (four thicknesses of a dollar bill is approxi-
mately 0.016") and place it between the support
bearing and the blade, as shown in Figure 53
#
8.
I^\]iZc i]Z XVe hXgZl id `ZZe i]Z hjeedgi
WZVg^c\adX`ZY^ceaVXZ#
Adjusting Lower Support Bearings
1.
9>H8DCC:8I76C9H6L;GDBEDL:G
2.
BV`ZhjgZi]Vii]ZWaVYZ^higVX`^c\egdeZgan
VcY^hXdggZXianiZch^dcZY#
3.
;Vb^a^Vg^oZ ndjghZa[ l^i] i]Z adlZg hjeedgi
WZVg^c\Xdcigdahh]dlc^cFigure 54#
I]ZWaVYZ\j^YZhegdk^YZh^YZ"id"h^YZhjeedgiid
]Zae `ZZe i]Z WaVYZ higV^\]i l]^aZ Xjii^c\# I]Z
WaVYZ\j^YZhVgZYZh^\cZYidWZVY_jhiZY^cild
lVnh·[dglVgY$WVX`lVgYVcYh^YZ"id"h^YZ#
]Zae `ZZe i]Z WaVYZ higV^\]i l]^aZ Xjii^c\# I]Z
WaVYZ\j^YZhVgZYZh^\cZYidWZVY_jhiZY^cild
lVnh·[dglVgY$WVX`lVgYVcYh^YZ"id"h^YZ#
To adjust the upper and lower blade guides:
1.
BV`ZhjgZi]ZWaVYZ^higVX`^c\egdeZganVcY
i]Vi^i^hXdggZXianiZch^dcZY#
2.
9>H8DCC:8I76C9H6L;GDBEDL:G
Adjusting Blade
Guide Bearings
4.
8]ZX`idbV`ZhjgZi]Z\j^YZWadX`VhhZb"
Wan^heZgeZcY^XjaVgl^i]i]Z[VXZd[i]Zhje"
edgiWZVg^c\Vh^aajhigViZY^cFigure 51#
edgiWZVg^c\Vh^aajhigViZY^cFigure 51#
·>[i]Z\j^YZWadX`VhhZbWan^heZgeZcY^Xj"
aVgidi]Z[VXZd[i]ZhjeedgiWZVg^c\!Xdc"
i^cjZdcidi]ZcZmihiZe#
i^cjZdcidi]ZcZmihiZe#
·>[ i]Z \j^YZ WadX` VhhZbWan ^h cdi eZg"
eZcY^XjaVg id i]Z hjeedgi WZVg^c\! addhZc
i]Z\j^YZWadX`VhhZbWanXVehXgZlhVcY
gdiViZ i]Z WaVYZ \j^YZ VhhZbWan h^YZ"id"
h^YZ jci^a i]Z WaVYZ ^h eZgeZcY^XjaVg l^i]
i]Z [VXZ d[ i]Z hjeedgi WZVg^c\! i]Zc gZ"
i^\]iZc i]Z XVe hXgZlh# Note: The table
must be re-aligned with the blade after the
lower guide block assembly is adjusted.
Refer to Page 35.
i]Z\j^YZWadX`VhhZbWanXVehXgZlhVcY
gdiViZ i]Z WaVYZ \j^YZ VhhZbWan h^YZ"id"
h^YZ jci^a i]Z WaVYZ ^h eZgeZcY^XjaVg l^i]
i]Z [VXZ d[ i]Z hjeedgi WZVg^c\! i]Zc gZ"
i^\]iZc i]Z XVe hXgZlh# Note: The table
must be re-aligned with the blade after the
lower guide block assembly is adjusted.
Refer to Page 35.
5.
AddhZci]ZXVehXgZldci]ZhjeedgiWZVg^c\
VY_jhibZcih]V[i#
6.
EaVXZ V %#%&+ [ZZaZg \Vj\Z WZilZZc i]Z
hjeedgi WZVg^c\ VcY i]Z WaVYZ! VcY edh^i^dc
i]ZWZVg^c\%#%&+VlVn[gdbi]ZWVX`d[i]Z
WaVYZ! Vh ^aajhigViZY ^c Figure 52! dg jhZ V
YdaaVgW^aa!Vhh]dlc^cFigure 53#
i]ZWZVg^c\%#%&+VlVn[gdbi]ZWVX`d[i]Z
WaVYZ! Vh ^aajhigViZY ^c Figure 52! dg jhZ V
YdaaVgW^aa!Vhh]dlc^cFigure 53#
7.
I^\]iZc i]Z XVe hXgZl id `ZZe i]Z hjeedgi
WZVg^c\adX`ZY^ceaVXZ#
Figure 54.
AdlZghjeedgiWZVg^c\Xdcigdah#
Hjeedgi
7ZVg^c\
6Y_jhibZci
H]V[i8Ve
HXgZl
Hjeedgi
7ZVg^c\
<j^YZ7adX`
6hhZbWan8VeHXgZl