Справочник Пользователя для Wagner SprayTech 9145

 

21

English

  1.  Remove the suction set.

  2.  Remove the front cover and the four screws that secure it 

using a T20 Torx head driver.  

  3.  Remove the yoke screw and washer that secures the 

dowel pin.  The dowel pin connects the yoke to the piston.

  4.  Using a pliers, pull the dowel pin out.

  5a.  For models 9145 and 9155, rotate the pump shaft so the 

piston is in the top dead center position.  This can be done 

by pushing on the yoke.  This is required to disassemble 

all the parts.

  5b.  For models 9175 and 9195, inspect the yoke assembly 

and piston. In order to remove all the necessary parts, the 

piston must not be in the bottom dead center position.  If 

the piston is at the bottom of the stroke, install the front 

cover and screws, turn the pump on briefly to index the 

piston, unplug the unit, and repeat step 2.

  6.  Unscrew and remove the inlet valve assembly (see page 

20).

  7.  Remove the piston assembly by pushing down on the 

piston near the yoke.  

  8.  Unscrew and remove the top nut using and adjustable 

wrench.  

  9.  Remove the worn seals using a flat head screwdriver or 

punch.  Remove the top seal from the top and the bottom 

seal from the bottom by pressing against the side of 

the seal and popping it out.  Be sure not to scratch the 

housing where the seals are located.

  10.  Clean the area where the new seals are to be installed.

  1.  Lubricate the new top seal with Separating Oil (P/N 

0516913, sold separately) or light household oil and by 

hand place the seal (cup side of seal down) into the top 

port of the housing.

  2.  Place a small amount of anit-seize on the threads of the 

top nut.  Place the top nut into the top of the housing and 

tighten with an adjustable wrench.  This will drive the top 

seal into the correct position.

  3.  Turn the pump upside down.  

Lubricate the seal on the piston/

seal assembly similar to the 

top seal.  Place the piston/seal 

assembly into the bottom of the 

housing.  Insert the plastic insertion 

tool and thread into position to 

properly seat the piston/seal.  

Thread fully until tight.  Remove the 

insertion tool.

  4.  Install the new O-ring on the inlet valve assembly, 

lubricate with Separating Oil (P/N 0516913), thread into 

the bottom (inlet) of the housing, and tighten with an 

adjustable wrench.  This will drive the bottom seal into the 

correct position. 

  5.  Align the piston with the yoke.  Be careful not to damage 

the piston.

  6.  Apply any type of household grease to the piston and yoke 

area to prolong life.  Apply to the holes in the yoke where 

the dowel is inserted.

  7.  Install the dowel pin to connect the yoke to the piston.  

The piston may have to be moved up or down to do this.

  8.  Install the yoke screw and washer to secure the dowel pin.

  9.  Turn pump right side up and apply a few drops of 

Separating Oil or light household oil between the top nut 

and piston.  This will prolong the seal life.

  10.  Install front cover and four (4) screws.

  11.  Replace inlet valve.  Install the suction set.

Insertion

tool

0512221 kit

(9145, 9155)
0512178 kit

(9175, 9195)

0512178 kit

(9175, 9195)

Top seal

(cup

down)

Top nut

0512221 kit

(9145, 9155)

Piston/seal

assembly

O-ring

Inlet valve assembly

Dowel

Yoke

Screw

Washer