Справочник Пользователя для Tascam D00871320A
About track editing
52
TASCAM DP-01 Owner’s Manual
Advanc
ed techn
iques
You can change the following values:
Src. Trk
This sets the source track or tracks from which the section is
copied. Choose
1
through
8
to select an individual track. Choose
1/2
,
3/4
,
5/6
or
7/8
etc. to select a pair of tracks. Choose
1-8
to select all tracks.
Dst. Trk
This sets the destination track or tracks into which the selected
section is inserted. What you can select here depends on what you have
selected for the source track. If you have selected a single track, you can
select tracks
selected for the source track. If you have selected a single track, you can
select tracks
1
through
8
here. If you have selected a pair of tracks (for
instance,
1/2
), you can only select track pairs here. If you have selected all
tracks (
1-8
), then
1-8
is the only option available to you here.
Times
This is the number of times that the selected section is inserted
(endtoend) in the destination track or tracks. You can set this value from
1
to
99
.
Press
YES
to perform the operation or
NO
to leave this screen.
MOVE -> PASTE
This function takes the section of a track or tracks marked by the IN
and OUT points, and moves it to the chosen track or tracks, starting
at the TO point.
and OUT points, and moves it to the chosen track or tracks, starting
at the TO point.
After the operation, the selected section of the source between the IN and
OUT points is replaced by silence.
OUT points is replaced by silence.
This operation overwrites anything which is already recorded at the desti
nation. The track is therefore the same length as it was before the operation.
nation. The track is therefore the same length as it was before the operation.
You can change the following values:
Src. Trk
This sets the source track or tracks from which the section is
taken. Choose
1
through
8
to select an individual track. Choose
1/2
,
3/4
,
5/6
or
7/8
to select a pair of tracks. Choose
1-8
to select all tracks.
Dst. Trk
This sets the destination track or tracks to which the selected
section is moved. What you can select here depends on what you have
selected for the source track. If you have selected a single track, you can
select tracks
selected for the source track. If you have selected a single track, you can
select tracks
1
through
8
here. If you have selected a pair of tracks (for
instance,
1/2
), you can only select track pairs here. If you have selected all
tracks (
1-8
), then
1-8
is the only option available to you here.
Press
YES
to perform the operation or
NO
to leave this screen.
MOVE -> INSERT
This function takes the section of a track or tracks marked by the IN
and OUT points, and moves it to the chosen track or tracks, inserting
it as new material, starting at the TO point.
and OUT points, and moves it to the chosen track or tracks, inserting
it as new material, starting at the TO point.
After the operation, the selected section of the source between the IN and
OUT points is replaced by silence.
OUT points is replaced by silence.
The insert operation adds the selected section as new material to the desti
nation. Nothing is overwritten on the destination, as any material following
the TO point is moved to the end of the newlyinserted section. The track is
therefore longer than it was before the operation.
nation. Nothing is overwritten on the destination, as any material following
the TO point is moved to the end of the newlyinserted section. The track is
therefore longer than it was before the operation.
Figure 2.6: Move and paste
OUT
IN
TO
OUT
IN
TO
Figure 2.7: Move and insert
OUT
IN
TO
OUT
IN
TO
DP-01_OM_E.book 52 ページ ２００５年６月１３日 月曜日 午後７時１４分