Справочник Пользователя для Master Appliance BT-30

Remove battery cover and place
alkaline battery size AA (1.5V) 
x 3 pcs. in correct position as 
illustrated (fig 1). Replace cover.

HOW TO MOUNT THE TIP (2)
• Align tip base over unit receptacle. 

Push inward until tip is fully seated on base.

• To remove ensure tip has cooled. Insert tip

remover plate supplied with unit at base of tip
and push tip away from base.

OPERATING INSTRUCTIONS
• Move slide switch forward to ON position. (Push button will not operate in OFF

position of slide switch for your safety.)

• Push button, pilot lamp will glow, tip will start to heat up. In about 10 seconds the

tip will heat up to melt the solder.

• When the pilot lamp becomes dark and it takes more than 30 seconds to start 

solder melting, the batteries may be exhausted. Replace with 3 new batteries.

• Power keeps running while pushing button and is cut off when the finger is off the

button. Make sure the finger is off the button right after soldering, otherwise the tip
keeps heat on while pushing button. Timely intermittent push on and off cycle will
make temperature control possible and battery life will be prolonged.

• To prolong tip life, tin the tip and make sure the slide switch is returned to OFF

position when not in use.

GENERAL SOLDERING INFORMATION
• For fast and accurate soldering, a clean and well-tinned tip is required. Heat and

gently wipe with a rag or emery cloth to clean tip. Re-tin to minimize oxidation. Use
good quality Solder; Rosin Core or Solid with the proper Flux for electronics work.
Apply Solder ONLY at  the point of the Tip.

STORAGE OF YOUR MICROPRO
• Allow unit to cool and put protective cap on for storage.
• If your unit is not going to be used for awhile, store in the following manner. 

Store in proper location avoiding elevated temperatures and away from children.

• Remove batteries before storage.

WARNING: To prevent the risk of injury or accident, READ and UNDERSTAND
the following warnings and how to use this tool. Keep this manual for future use.

IMPORTANT SAFETY INSTRUCTIONS
1. Do not touch the tip, as it is extremely hot.
2. Do not strike or apply excessive pressure on the tip assembly.
3. When cleaning the tip with wet sponge, do not apply excessive water as it cools.
4. After use, make sure to return the slide switch to OFF position for safety.
5. While not in use, take batteries out of the tool and keep protective cap on.
6. Do not try to alter or tamper with the tool. Use only genuine parts.
7. Store away from and do not use in the presence of children.
8. Use local exhaust when soldering.

WARNING: This product, when used for soldering and similar applications, produces chemicals
known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING: The FAA prohibits air transportation of devices that contain batteries unless
properly prepared and protected from conditions that may create heat or fire. Batteries
must be removed from this unit while in transport either as carry-on or checked baggage.

BATTERY USE
• Make sure to use alkaline batteries, size AA (1.5V), 3 pcs. Other types of batteries

might fail to perform as designed.

• Heat up time becomes longer as the battery is used. Replace batteries with new

when heat up time becomes increased.

• Place batteries into unit per diagram to function properly. (fig 2)
• Do not put batteries in fire, nor abuse as short circuit, heat, charge. Those will

result in damage, fire, injury and contamination.

• Do not try to solder a battery, as it might cause fire, injury and contamination.
• Do not touch liquid that has leaked out of a battery.
• If a damaged battery is touched, wash down with water.
• If liquid leaks out of batteries in the iron body, wipe it up and replace with new batteries.
• When not using the iron for a long period, take batteries out of the body.
• Do not mix new and old batteries and/or different types together at a time in the iron.
• Batteries are not rechargeable as supplied with unit.