Справочник Пользователя для Fisher & Paykel CG903MLD
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our
local website listed at the end of this document or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
Important safety precautions!
Particular attention shall be given to the relevant requirements regarding ventilation.
Please make this information available to the person installing the appliance as it could reduce your
Please make this information available to the person installing the appliance as it could reduce your
installation costs.
This appliance is to be installed and connected to the electricity and gas supply only by an authorised
person.
Installation must comply with your local building and local gas authority codes and electricity
regulations.
Failure to install the appliance correctly could invalidate any warranty or liability claims.
These appliances are registered in: (New Zealand) at www.ess.govt.nz and (Australia) with SAI Global
These appliances are registered in: (New Zealand) at www.ess.govt.nz and (Australia) with SAI Global
at www.saiglobal.com.
This gas appliance is suitable for connection to natural gas only. If in doubt, refer to the local gas
network operator or gas supplier to confirm gas type at installation site.
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Electrical shock hazard
Disconnect appliance from main power supply before continuing.
Failure to do so could result in electrical shock or death.
Before you install the appliance, please make sure that
the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance
are compatible. For adjustment conditions for this appliance, see ‘Gas rate summary’
a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to
comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm
air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with
the wiring rules, unless the local wiring rules allow for alternative means
air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with
the wiring rules, unless the local wiring rules allow for alternative means
the appliance is connected to a 220V - 240V 50Hz (10 A) power supply only and earthed via the
power supply cable
there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the
product). This must be accessible after installation. The power supply cable should not touch any
metal parts
metal parts
if the power supply cable is damaged, it is replaced only by the special cable: Part no. 531953 - Flex
Terminal Block Assy NZ/AU, obtainable from authorised Fisher & Paykel Service Agents
the supply connection point (gas shut-off valve) is accessible after installation
the benchtop is made of a heat resistant material
the installation complies with all the requirements of Australian and New Zealand Gas Installation
the benchtop is made of a heat resistant material
the installation complies with all the requirements of Australian and New Zealand Gas Installation
Standards (AS5601, NZS5261), including that the product has to be installed so that the surface
temperature of any nearby combustible surface will not exceed 65
temperature of any nearby combustible surface will not exceed 65
O
C above ambient. See 3
‘Clearance Dimensions’.
When you install the appliance
We do not recommend you flush mount or seal this appliance into the bench with silicone or glue.
Doing so will make future servicing difficult. Fisher & Paykel will not be liable for any costs associated
with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred
by doing this.
with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred
by doing this.
Seal exposed bare edges of the cutout with an oil-based paint or moisture-proof polyurethane to
prevent possible moisture creeping between the cooktop trim and the benchtop.
We do not recommend the use of a down-draught extractor fan with the appliance, as it may distort
the flame pattern, causing uneven heating and reduced cooking performance.
Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater.
No combustible material or products should be placed on this appliance at any time.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
If, after following the instructions given, the appliance cannot be adjusted to perform correctly,
No combustible material or products should be placed on this appliance at any time.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
If, after following the instructions given, the appliance cannot be adjusted to perform correctly,
please refer to the Service & Warranty book for warranty details and your nearest Authorised Service
Centre, Customer Care, or contact us through our website: www.fisherpaykel.com.
Centre, Customer Care, or contact us through our website: www.fisherpaykel.com.
1
IZONA CookSurface
Installation instructions
CG903ML & CG903MLD models
NZ AU