Справочник Пользователя для Saeco Coffee Makers Type SIN024X
ENGLISH
• 23 •
4
INSTALLATION
For your own safety and the safety of
others, you must strictly comply with the
“Safety Rules” described in section 3.
others, you must strictly comply with the
“Safety Rules” described in section 3.
4.1 Packaging
The original packaging was designed and
made to protect the machine during shipping.
We recommend keeping it for future transport
purposes.
made to protect the machine during shipping.
We recommend keeping it for future transport
purposes.
4.2 Installation precautions
Before installing the machine, make sure to
follow these safety precautions:
• put the machine in a safe place;
• make sure that children are not allowed to
follow these safety precautions:
• put the machine in a safe place;
• make sure that children are not allowed to
play with the machine;
• avoid placing the machine on very hot
surfaces or near open flames.
Now the coffee machine is ready to be
connected to the mains power supply.
connected to the mains power supply.
4.3 Mains connection
Electricity can be dangerous! There-
fore, always strictly abide by the
fore, always strictly abide by the
safety rules.
Never use defective cords!
Defective cords and plugs must be
Defective cords and plugs must be
immediately replaced by an Authorised
Service Centre.
The coffee machine must be plugged into a
suitable electric socket.
The voltage of the appliance is factory set.
Check that the mains voltage matches the
rating specified on the identification plate on
the bottom of the appliance.
•
Service Centre.
The coffee machine must be plugged into a
suitable electric socket.
The voltage of the appliance is factory set.
Check that the mains voltage matches the
rating specified on the identification plate on
the bottom of the appliance.
•
Before plugging in the machine, make sure
the ON/OFF switch is not pressed (2).
the ON/OFF switch is not pressed (2).
• (Fig.4A) - Put the socket into the outlet on
the rear of the machine.
• Connect the other socket to a wall outlet
having the proper voltage.
4.4 Filling the water tank
• (Fig.1) - Remove the water tank (1) taking
care not to damage the water suction tube.
• (Fig.2) - Rinse out the tank and fill it with fresh
drinking water, taking care not to overfill.
• (Fig.3) - Fit the tank again in its position,
and place the tube previously removed.
Always fill the tank with fresh, still
drinking water.
drinking water.
Hot water and/or other liquids may dama-
ge the tank. Always make sure that there is
sufficient water in the tank before starting
the machine.
ge the tank. Always make sure that there is
sufficient water in the tank before starting
the machine.
4.5 Loading the circuit
Before starting the machine, if it has been
inoperative for a long time and all the water has
been used up, you must reload the circuit.
• (Fig.4B) - Press the ON/OFF switch (2). The
inoperative for a long time and all the water has
been used up, you must reload the circuit.
• (Fig.4B) - Press the ON/OFF switch (2). The
light (3) will go on.
• (Fig.5) - Place a container beneath the steam
tube. Turn the “hot water/steam” knob (7)
counterclockwise to open.
counterclockwise to open.
• (Fig.6) -
Press the coffee switch (4).
• Wait until a steady stream of water flows from
the steam tube (“pannarello”).
•
Press the coffee switch (4) again. Turn the
“hot water/steam” knob (7) clockwise to shut
off flow (Fig.7). Remove the container.
“hot water/steam” knob (7) clockwise to shut
off flow (Fig.7). Remove the container.
The machine is now ready to dispense coffee
and steam; for a description of machine
functions, see the specific sections.
and steam; for a description of machine
functions, see the specific sections.
5
MAKING COFFEE
Warning!
While the brew unit is operating it
While the brew unit is operating it
is forbidden to remove the “Crema” filter
holder by manually turning it clockwise.
Danger of burns!
• During this operation the temperature ready
holder by manually turning it clockwise.
Danger of burns!
• During this operation the temperature ready
light (5) may go on and off; this is normal
and not to be considered a fault.
and not to be considered a fault.
Installation
4316036000 - SIN024X Rev00.indd 23
10/05/2004 11.57.18