Листовка для American Standard 6030Y2A.102.XXX
7 5 4 2 8 3 - 1 0 0 R e v . A
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 8
© A S A m e r i c a , I n c . 2 0 0 8
INSTALLATION INSTRUCTIONS
Model 6030Y2A.102.XXX
Model 6030Y2A.202.XXX
Model 6030Y2A.202.XXX
Acrylux Builder Series (Above Floor Rough)
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please
read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
6030Y2A.102.XXX
6030Y2A.202.XXX
6030Y2A.202.XXX
STUD LAYOUT:
The American Standard Acrylux Bathtub
will fit all standard 30" x 60" tub walls.
The American Standard Acrylux Bathtub
will fit all standard 30" x 60" tub walls.
INSTALLATION INSTRUCTIONS
STEP 1. PREPARING ALCOVE
• Strip to bare studs.
• Alcove studs should be constructed as shown above.
• Floor must be clean, smooth, and level (check with level). Sub floor must
be installed as in the stud layout. Do not install tub on open floor joists.
• If required, cut hole in sub floor as shown above to accommodate drain.
STEP 2. INSTALLING TUB
• Trial fit tub in prepared alcove. With tub sitting flat on floor, check with
level on top of tub. Tub should be level from front-to-back and
side-to-side (Fig 1).
side-to-side (Fig 1).
• A floor leveling compound (smooth mortar) or a similar quick-setting
compound specifically made for leveling floors may be used to fully
support and level base.
support and level base.
• After tub is leveled, if alcove is larger than tub, shim between tub and
studs to create a tight fit. Screw tub flange to studs (Fig. 2).
IMPORTANT:
• Allow tub to reach room temperature before installation.
• Read installation instructions carefully before starting project.
• Keep instructions for warranty information.
• Read installation instructions carefully before starting project.
• Keep instructions for warranty information.
31-1/2"
800mm
800mm
60"
1524mm
10"
254mm
14"
356mm
356mm
6"
152mm
152mm
8"
203mm
203mm
Drain C
L
Floor Cut Out
6" x 10"
(152 x 254mm)
= stud location
19"
483mm
30"
762mm
18"
457mm
1"
25mm
59-7/8"
1521mm
RECOMMENDED TOOLS AND MATERIALS
Tape
Measure
Mortar
Compound
(optional)
Pencil
Saber
Saw
Safety
Glasses
Screws,
1"
Flathead,
Stainless
Drill
Level
FIGURE 1. Check to assure tub is level.
FIGURE 2. If necessary, shim between tub and studs
for tight fit and screw to each stud.
for tight fit and screw to each stud.
CLEANING
• Do not use any abrasive cleaners or metal scrapers.
• If drywall mud or plaster gets on your shower, it may be carefully removed
with a wooden scraper made from a piece of scrap wood.
• Adhesive may be removed with mineral spirits.
• Ideal cleaners are Soft Scrub Gel
• Do not use any abrasive cleaners or metal scrapers.
• If drywall mud or plaster gets on your shower, it may be carefully removed
with a wooden scraper made from a piece of scrap wood.
• Adhesive may be removed with mineral spirits.
• Ideal cleaners are Soft Scrub Gel
®
or Comet Gel
®
.
WARNING:
Some cleaning products are not suitable for use. Read all labels carefully.
DO NOT USE if they say “not suitable for use with ABS, acrylic, or polystyrene.
DO NOT USE if they say “not suitable for use with ABS, acrylic, or polystyrene.
LHO shown - Reverse for RHO