Справочник Пользователя для Liebherr FI1051

Particles  may  accumulate  in  the  IceMaker  or  water  line

the  first  time  the  appliance  is  used  or  after  an  extended

period out of service.

u

To achieve this, do not consume or use the ice cubes

that are produced within 72 hours.

The  opening  time  of  the  valve  on  the  IceMaker  can  be

adjusted if, for example, the water pressure in the pipe is

too low or too high.
The water supply time can be set in stages from 

E1

 (short

supply time) to 

E8

 (long supply time). The default setting

is 

E3

.

u

Activate  setting  mode:  press  and  hold  the  SuperFrost

button

 Fig. 2 (9)

 for approximately 5 s.

w

S

 is shown on the display.

w

The Menu symbol

 Fig. 2 (3)

 lights up.

u

Using the Up button

 Fig. 2 (1)

 or Down button

 Fig. 2 (2)

,

select 

E

.

u

To  confirm:  briefly  press  the  SuperFrost  button

Fig. 2 (9)

.

u

To increase the water supply time: press the

Up button

 Fig. 2 (1)

.

u

To decrease the water supply time: press the

Down button

 Fig. 2 (2)

.

u

To  confirm:  press  the  SuperFrost  button

Fig. 2 (9)

.

u

Deactivate  setting  mode:  press  the  On/Off  button

Fig. 2 (8)

.

u

Wait 5 mins.

w

The temperature is again displayed on the temperature

display.

When  the  IceMaker  is  switched  off,  the  drawer  of  the

IceMaker can also be used for freezing and storing food.

u

Press  the  On/Off  button  for  about  1  second  until  the

LED goes out.

u

Clean the IceMaker.

w

This  ensures  that  no  water  or  ice  remains  in  the

IceMaker.

The water filter should be changed when the Filter symbol

Fig. 2 (5)

 lights up. It should be replaced every six months

at least or whenever you notice a significant decrease in

the  flow  rate  You  can  order  one  from  your  dealer  or  by

visiting our web site at www.liebherr-appliances.com.
The  used  water  filter  contains  activated  carbon  and  can

be disposed of with normal household waste.
To remove the old water filter:

Fig. 5 

u

lift the ventilation grid 

Fig. 5 (1)

 up and pull out.

u

Open the filter change flap

 Fig. 5 (2)

.

u

Pull the water filter carriage

 Fig. 5 (3)

 out.

u

Remove the filter cover

 Fig. 5 (6)

.

u

Catch any dripping water with your hand or with a dish.

u

Turn the water filter

 Fig. 5 (3)

 about 100° anti-clockwise

and pull out.

If no new water filter is inserted:

u

put the filter cover on to protect the filter unit from dirt

and dust.

Fig. 6 

u

Insert  the  new  filter

  Fig.  6  (4)

  and  turn  it  about  100°

clockwise as far as it will go.

u

Place the cover

 Fig. 6 (6)

 on the filter.

u

Write  the  date  of  the  next  filter  replacement  on  the

supplied adhesive label

 Fig. 6 (5)

 and affix it to the filter

cover

 Fig. 6 (6)

.

u

Push in the water filter carriage

 Fig. 6 (4)

.

u

Close the filter change flap

 Fig. 6 (3)

.

u

Fit the ventilation grid

 Fig. 6 (1)

 again and push down. It

must close flush with the floor.

New water filters may contain particulate matter.

u

Do not consume or use ice cubes produced within 72

hours after replacing the filter.

u

Remove any ice still present in the IceMaker tray. You

can keep this ice in another tray for later use.

u

Make  sure  the  filter  does  not  leak  and  no  water  is

coming out.

u

Select  setting  mode:  Press  and  hold  the  SuperFrost

button

 Fig. 2 (9)

 for approx. 5 seconds.